1958 Ford F-100 on 2040-cars

Auto blog

Ford builds Lightweight Concept with Fusion shell [w/video]

It's a fairly well known fact that removing weight from a car is essentially a panacea for many of the modern automobiles problems. Does it handle like crap? Remove weight. Underpowered? Don't add power; trim the fat. Need to improve fuel economy? It's diet time.
Actually executing a major weight reduction program, though, much like with human beings, is no easy task. Unlike you or I, where motivation is the issue, the prohibitive measure in trimming a car's waistline is money. Lightweight materials are expensive, with carbon fiber and carbon-fiber reinforced plastic still primarily in the domain of higher end vehicles. Even aluminum construction, pioneered on a mass-produced level by Audi and Jaguar, is only now starting to make its way into the mainstream, thanks to the upcoming Ford F-150.
With this concept, though, Ford is attempting to show that a mass-produced, lightweight vehicle isn't too far off. This is the Lightweight Concept, and while it may look like a Fusion, it weighs as much as a Fiesta. For reference, the lightest Fusion available to the public is the 3,323-pound, 2.5-liter model with a manual transmission. A manually equipped, 1.6-liter Fiesta, meanwhile, is just 2,537 pounds.

Here's what the UAW will be angling for in next year's contract negotiations

The United Auto Workers union is about to enter a new round of negotiations with the Detroit Three automakers, and this time, the focus is on the end of the two-tier wage system. Introduced in 2007, the two-tier wage system was enacted to allow General Motors, Ford and Chrysler to categorize its hourly employees under two categories: Tier 1 for veteran employees with full rights and benefits, and Tier 2 for short-term or entry-level employees compensated under a different schedule. The idea was that the system would permit the automakers to invest more in their plants and hire new employees as part of their respective recovery plans without being saddled with all the costs associated with hiring full-time employees. Now that the automakers are (more or less) back on their proverbial feet, however, the UAW wants to see an end to the two-tier system, and will likely make that a center-point of its negotiations next year to replace the current arrangement that is scheduled to end in September 2015. Not all members of the UAW will necessarily be interested in ending the two-tier system, however. According to The Detroit News, some Tier 1 workers may be more interested in negotiating a raise in their hourly rate – something which they haven't received in almost a decade. Tier 2 workers, meanwhile, may be more motivated to keep the tiered system in place, as their arrangement includes provisions for profit-sharing payments that have seen the automakers pay out billions to so-called short-term employees in lump-sum payments. Reconciling the two competing demands from two categories of union members and presenting a united front in negotiations may prove the biggest challenge for the UAW's new president, Dennis Williams. And with the right to strike – something which was suspended during the last round of negotiations in 2011 – the union has a bigger bargaining chip in its pocket.

Watch these videos of an NHRA racer's bodywork blowing off into a crowd

Just a few months ago, fan safety at racetracks was a hot topic following the last-lap NASCAR Nationwide Series crash at Daytona that sent large pieces of racecars into the grandstands injuring 33 fans. Now, a freak incident at a National Hot Rod Association event resulted in a drag racer's bodywork flying into the crowd at the NHRA Four-Wide Nationals in Charlotte over the weekend. The carbon-fiber body of Robert Hight's Ford Mustang funny car blew off toward the end of a run when his engine exploded, but fortunately, the two fans evaluated after the incident were later released without serious injury.
As you can see in the image above, the body flew high into the air before landing on a walkway in front of the grandstands, a bit of happenstance that likely gave most fans enough time and space to move out of the way. Scroll down to watch a couple of videos showing what happened, including one from a fan's perspective that also reveals what appears to be part of the body's metal bracing landing dangerously close to the crowd.