2004 Ford Excursion Limited 4x4 Lifted Monster!! Superduty, Must See!!! on 2040-cars

Auto blog

Takata adds millions to recall expansion in US [UPDATE]

UPDATE: Ford spokesperson Kelli Felker has advised Autoblog that of the 1,509,535 total vehicles worldwide that the company is recalling, 966,504 of them are new additions for this expanded safety campaign. Last week, the National Highway Traffic Safety Administration announced that the Takata airbag inflator recalls would expand to an estimated 33.8 million vehicles in the US. However at the time, automakers weren't sure specifically which of their models might be affected under this enlarged campaign. Now, the numbers for BMW, FCA, Ford, and Mitsubishi are being released by the agency. Additionally, Honda is outlining the broadening of its own campaign. BMW's recall amounts to 420,661 vehicles in the US, an increase from 140,696 previously. All of the following models need their front, driver's side airbag replaced: 2002-2005 BMW 325i/325xi/330i/330xi Sedan 2002-2005 BMW 325xi/325i Sportswagon 2002-2006 BMW 330Ci/325Ci/M3 Convertible 2002-2006 BMW 325i/330i/M3 Coupe 2002-2003 BMW M5/540i/525i/530i Sedan 2002-2003 BMW 540i/525i Sportswagon 2003-2004 BMW X5 3.0i/4.4i BMW has received no reports of any injures or deaths from this problem in its vehicles. FCA has 5,224,845 vehicles globally in need of inflator replacements, according to its statement. However, the company is only aware of one injury related to the issue, which occurred in a 2006 Dodge Charger in southern Florida. There are 4,747,202 vehicles worldwide from the company that are affected on the front, driver's side. Among these, 4,066,732 are in the US, 374,508 are in Canada, and the rest are in other countries. The models are: 2005-2009 Dodge Ram 2500 Pickup 2004-2008 Dodge Ram 1500 Pickup 2006-2009 Dodge Ram 3500 Pickup 2007-2009 Dodge Ram 3500 Cab Chassis 2008-2010 Dodge Ram 4500/5500 Cab Chassis 2008-2009 Sterling 4500/5500 Cab Chassis 2004-2008 Dodge Durango 2007-2008 Chrysler Aspen 2005-2010 Chrysler 300/300C/SRT8 2005-2010 Dodge Charger/Magnum 2005-2011 Dodge Dakota 2006-2010 Mitsubishi Raider Also, there are 438,156 vehicles in the US, according to the NHTSA documents, that need their front passenger's side inflators replaced in the expansion of an earlier regional recall: 2003 Dodge Ram 1500 2003 Dodge Ram 2500 2003 Dodge Ram 3500 The total number of vehicles from Ford now covered under these campaigns stands at 1,509,535 worldwide. Of this total, there are 1,380,604 in the United States, 93,207 in Canada and 16,953 in Mexico.

These horribly misguided front-drive design studies nearly became the Mustang

As we eagerly await the unveiling of the all-new sixth-generation Mustang, Ford has been giving us some great information over the past few months showing what has gone into shaping its venerable pony car. As many changes as the Mustang has gone through in its 50 years, though, it appears the fourth-gen model played a decisive and pivotal role in the car's future.
As is part of Mustang lore, the front-wheel drive Ford Probe was originally developed as a next-generation Mustang in the Eighties before cooler heads prevailed. The Blue Oval has just released a handful of images showing how bad things could have been - including a full-scale clay model of a front-wheel-drive Mustang (shown above). Fortunately, the FWD Mustang plan was scrapped and Ford went to work designing a rear-wheel-drive replacement for the Fox Body Mustang, with three design studies making it far enough to become full-scale models. These include the soft "Bruce Jenner" Mustang, the over-the-top "Rambo" Mustang and the middle-ground "Arnold Schwarzenegger" Mustang, which finally became the basis for the 1994 'Stang.
By early 1991, the design language of the fourth-generation Mustang had been worked out, and the rest, they say, is history. Scroll down for the fascinating press release telling the story of the fourth-gen Mustang, and be sure to check out the gallery of horribly misguided sketches and various design studies that were all on the table in the late 1980s.

Plug In 2014: ALTe ready to join Ford's EQVM to convert, sell F-150 PHEV [w/video]

It's been a while since we've checked in with ALTe and its plans to convert big work vehicles like the Ford F-150 into plug-in hybrids. So, when we saw a demonstration vehicle sitting outside the San Jose Convention Center at the Plug In 2014 Conference last week, we had to get a closer look. When we did, we realized that it's been quite some time since we've been in a Ride & Drive vehicle that was all beat to heck. It's been quite some time since we've been in a Ride & Drive vehicle that was all beat to heck. The reason for the well-worn F-150 with 30,000 miles on it is that ALTe has been showing off its extended-range EV technology to lots of people all around the country, and Kyle Maki has been the man on the scene more often than not. "This one, I've taken all over the country," he told AutoblogGreen. "I've wore out that seat, I think. The only reason this one wasn't driven here was because we were in Charlotte [NC] last week and I didn't want to take a chance and not make it in time for this event." In other words, ALTe is out there, ginning up excitement for the idea of a plug-in hybrid Ford with an electric range of up to 40 miles and which can then continue on gas for another 360 miles at around about 25 miles per gallon. ALTe wants to not only convert new vehicles but it also offers retrofits for fleets that are happy with their current fleet. The company offers converted versions of the Ford E350 and E450 utility vehicles now but the near-mythical F-150 PHEV is still "coming soon." Yes, orders are now being accepted, but you will be forgiven if you think this is all happening on a slow time scale. There are simply a lot of things to do before ALTe can sell the truck. ALTe is currently attempting to join Ford's EQVM program, which is the electric version of the standard Qualified Vehicle Modifiers program. The QVM program requires coachbuilders to "be successfully evaluated by Ford Motor Company on criteria such as engineering, the manufacturing process, quality control, and adherence to Ford and Lincoln Divisions guidelines." Qualified applicants must also meet all applicable Federal Motor Vehicle Safety Standards, conform to Ford/Lincoln conversion guidelines and agree to be inspected annually as well as have a "commitment to continuous improvement." Maki has a simpler explanation. "It basically means you're a preferred supplier, a Tier 1, if you will," he said.