Like New 2012 Ford Escape Xlt V6 Repairable Salvage Struck By Lightning 7 Miles on 2040-cars

Auto blog

Ford finds flex-fuel engine design plays big role in emissions output

How bad is ethanol for your engine? There's been a lot of debate on this issue as the US considers upping the biofuel content in the national gasoline supply from 10 percent (E10) to 15 percent (E15). The ethanol industry and some scientists say higher ethanol blends show no "meaningful differences" in new engines while the oil industry says ethanol creates health risks. Researchers working at the Ford Research and Innovation Center decided to take a closer look at how a wide range of gas-ethanol blends - E0, E10, E20, E30, E40, E55 and E80 - affected the emissions coming out of a flex-fuel 2006 Mercury Grand Marquis. To see the full report, printed in the journal Environmental Science & Technology, requires payment, but there is an abstract and Green Car Congress has some more details. The gist is that, "with increasing ethanol content in the fuel, the tailpipe emissions of ethanol, acetaldehyde, formaldehyde, methane, and ammonia increased." At least NOx and NMHC emissions decreased. The researchers say that the effects are due to the fuel and "are expected for all FFVs," but that the way that a manufacturer calibrates the engine will affect NOx, THC, and NMOG emissions. It's this last bit that's important, since the researchers found, "Higher ethanol content in gasoline affects several fundamental fuel properties that can impact emissions. ... These changes can have positive or negative effects that can depend on engine design, hardware, and control strategy. In addition to direct emissions impacts, higher ethanol content fuel can also provide more efficient combustion and overall engine operation under part-load conditions and under knock-limited higher-load conditions." So, as we head towards more ethanol in our fuel supply (maybe), manufacturers are going to need to learn how to burn it most efficiently.

Ford confirms 1.5-liter EcoBoost four-cylinder engine for 2014 Fusion

Earlier this week, reports were swirling 'round the internet about the 2014 Ford Fusion getting a new 1.5-liter three-cylinder EcoBoost engine. That was... half correct. Ford today confirmed that the 2014 Fusion is, in fact, getting a new 1.5-liter EcoBoost mill, but it has four cylinders, not three.
The new 1.5-liter engine will be the fifth EcoBoost powerplant from Ford Motor Company. Initially to be built at the automaker's Craiova, Romania plant, it will also be offered in the Fusion's twin, the Mondeo, in other markets. This engine will debut at the Shanghai Motor Show next month, and the 1.5-liter is of particular importance in the Chinese market - there is significant tax relief in the People's Republic for vehicles powered by engines with a capacity of 1.5 liters or less.
At a media briefing Thursday, Ford declined to divulge exact power or fuel economy numbers, though Joe Bakaj, vice president of powertrain engineering, told Autoblog that power output should be similar to that of the current 1.6-liter inline-four, and that overall efficiency will be "better than the 1.6." Our earlier report stated that the 1.5-liter four will produce 177 horsepower and 177 pound-feet of torque - losses of 1 hp and 7 lb-ft versus the 1.6-liter engine. Ford states that the 1.5-liter four will feature many of the same technologies used on the company's 1.0-liter EcoBoost inline-three, including an integrated exhaust manifold that recaptures much of the engine's heat.

NHTSA closes Ford F-Series Super Duty steering probe without recall

The National Highway Traffic Safety Administration's investigation into 2008 Ford F-250 and F-350 Super Duty pickups, which was originally opened last year, has now ended without a recall. NHTSA was looking into steering failures on some 336,000 trucks.
The issue rested with the steering gear - NHTSA received five complaints of failures - which was redesigned in 2005. According to the report on the matter, investigators "found evidence of broken sector shaft gear teeth and piston damage consistent with incidents of single event overload."
NHTSA investigators, however, "found no evidence of fatigue or material property defects in any of the fractures. Analysis of complaint rates by vehicle build month showed no patterns indicating potential manufacturing quality issues and no difference before and after Ford introduced design changes to the input shaft and sector shaft seals in July 2007 to address potential leak concerns," according to the report, obtained by The Detroit News.