2011 Ford Edge Sel Sport Utility 4-door 3.5l on 2040-cars

Auto blog

UK's Loughborough University improving Ford's 1.0-litre EcoBoost engine

How much does it cost for college students to study zero emissions vehicles? At Loughborough University in the UK, a new Advanced Propulsion Centre (APC) is being built at a cost of a billion pounds ($1.7 billion US). The school has just announce that it will fund a number of grad student positions and is creating a new Chair in Advanced Propulsion Systems, which sounds like a fun job to us. We're weird like that. There will be a total of four professor-type positions in the new Center, including the chair, all focused on teaching students about low-carbon vehicle technologies, specifically electric and hybrid ones. The school is investing 1.5 million pounds ($2.5 million) for the new positions. There is a bigger picture as well, a 26-million pound ($44 million) Advanced Combustion Turbocharged Integrated Variable-valvetrain Engine (ACTIVE) project, which uses funds not only from the school but also from Ford and others. The point of ACTIVE is to study Ford's 1.0-liter EcoBoost engine and "improve further its efficiency and ensure it exceeds 2020 emission regulations." This is already a popular engine for the automaker, and it will need to stay at the bleeding edge of efficiency to remain as important in 2020 as it is today. Loughborough University has been working with automakers on advanced energy technologies for years, for example with Rolls-Royce and fuel cells in 2007 and the Lotus Hotfire engine in 2008. University invests GBP1.5M in advanced propulsion research to advance zero emissions vehicles challenge Loughborough University is investing GBP1.5M over five years in strategic research appointments, inspired by the global challenge to develop the new advanced propulsion technologies required for the move to zero emission vehicles. These appointments reinforce the University's world-class research in low-carbon vehicle technologies, adding new dimensions concerned with electric and hybrid drives. Four appointments will be made, including a Chair in Advanced Propulsion Systems, supported by a number of PhD studentships. The GBP1.5M investment is part of the University's commitment to the recently announced Advanced Propulsion Centre (APC) to support the development of new supply chains for low carbon vehicles. APC is an initiative established by the Automotive Council that will see GBP1 billion of investment from government and industry over the next 10 years.

Ford and Chrysler reducing summer plant shutdowns

Most domestic automaker assembly plants traditionally take a couple of weeks off during the summer. The shutdowns give each plant time for much needed repairs and maintenance, and in some cases, help better align production with demand. Not this year, though, as demand for many models is outstripping what Ford, Chrysler and General Motors plants can produce.
Ford has announced that it will shorten its annual summer shutdown for most North American plants from two weeks to one. The shorter shutdown will increase the carmaker's annual North American production by 40,000 units on top of the 200,000 extra units that it was already planning to produce this year versus last. Automotive News reports that Ford produced 2.8 million vehicles on this continent in 2012, and that output this year has already increased 13 percent through April.
Chrysler, meanwhile, is also operating at full tilt and plans to run some plants through the summer with no shutdown at all. Those not getting a break include Jefferson North where the Jeep Grand Cherokee and Dodge Durango are assembled, Toledo North that will assemble the new Cherokee, and Conner Avenue, home of SRT Viper production. Other assembly plants will be down for a single week, while all of Chrysler's engine and transmission plants except one in Indiana will continue operating with no shutdown this summer.

Ford debuts Fusion NASCAR racer that edges closer to stock [w/video]

The sixth-generation NASCAR Sprint Cup racecar, which will make its competition debut at the 2013 Daytona 500 this weekend, marks the closest thing to a "stock car" that the sport has seen in more than 20 years. No longer using just stickers to distinguish the different brands, the image above shows the lengths NASCAR and automakers went in order to create a racecar design that more closely resembles the individual cars they represent.
Ford, one of the more open and vocal OEMs regarding the Gen6 car's development, is giving us a closer look at its racing version of the Fusion with a pretty revealing side-by-side comparison with last years' racer (click above for an expanded view). Aside from the more realistic front end and production-like body lines, the overall shape, dimensions and proportions have also been designed to give the racecar a more stock appearance. Most of the new racer was designed by the Ford Design Center, which the automaker says was the first time it has been so involved in the design process since the 1960s. Of course, one area the Sprint Cup Fusion really differs from the production Fusion is its Ford Racing 5.8-liter V8 producing around 850 hp. Can you say Fusion SVT?
Scroll down for a quick video from Ford Racing showing a production Fusion morph into a Cup car.