Ford E-450 Elder Bus Wheelchair Accessible Lift Etc... on 2040-cars

Auto blog

UK's Loughborough University improving Ford's 1.0-litre EcoBoost engine

How much does it cost for college students to study zero emissions vehicles? At Loughborough University in the UK, a new Advanced Propulsion Centre (APC) is being built at a cost of a billion pounds ($1.7 billion US). The school has just announce that it will fund a number of grad student positions and is creating a new Chair in Advanced Propulsion Systems, which sounds like a fun job to us. We're weird like that. There will be a total of four professor-type positions in the new Center, including the chair, all focused on teaching students about low-carbon vehicle technologies, specifically electric and hybrid ones. The school is investing 1.5 million pounds ($2.5 million) for the new positions. There is a bigger picture as well, a 26-million pound ($44 million) Advanced Combustion Turbocharged Integrated Variable-valvetrain Engine (ACTIVE) project, which uses funds not only from the school but also from Ford and others. The point of ACTIVE is to study Ford's 1.0-liter EcoBoost engine and "improve further its efficiency and ensure it exceeds 2020 emission regulations." This is already a popular engine for the automaker, and it will need to stay at the bleeding edge of efficiency to remain as important in 2020 as it is today. Loughborough University has been working with automakers on advanced energy technologies for years, for example with Rolls-Royce and fuel cells in 2007 and the Lotus Hotfire engine in 2008. University invests GBP1.5M in advanced propulsion research to advance zero emissions vehicles challenge Loughborough University is investing GBP1.5M over five years in strategic research appointments, inspired by the global challenge to develop the new advanced propulsion technologies required for the move to zero emission vehicles. These appointments reinforce the University's world-class research in low-carbon vehicle technologies, adding new dimensions concerned with electric and hybrid drives. Four appointments will be made, including a Chair in Advanced Propulsion Systems, supported by a number of PhD studentships. The GBP1.5M investment is part of the University's commitment to the recently announced Advanced Propulsion Centre (APC) to support the development of new supply chains for low carbon vehicles. APC is an initiative established by the Automotive Council that will see GBP1 billion of investment from government and industry over the next 10 years.

Ford F-Series Super Duty prototype reduced to smoldering mess of aluminum and steel [UPDATE]

The most important bit of information you need to know after looking through our high-res gallery of images depicting a prototype 2016 Ford F-Series Super Duty pickup truck burning to the ground is that nobody was hurt. There were two engineers inside the vehicle when it caught fire, and both exited to safety.
That's the good news. The bad news is that the truck, which appears to have been testing in Death Valley, appears to be a total loss, minus, of course, whatever information Ford can glean from the conflagration - particularly tracing it back to its root cause. Besides that, we're also expecting the body of the next Super Duty to be hewn from aluminum, as is the case with its smaller brother, the brand-new F-150. Note the little aluminum droppings littering the roadway as apparent proof of that.
Our spy photographers report that it took just 21 minutes for the F-Series Super Duty to burn completely to the ground. The fire appears to have started in the driver-side front wheel well, spreading to engulf the entire front end in three minutes. We can't confirm the source of the blaze, but we're curious if the car's black vinyl cladding, meant to obscure the secrets within, contributed to the fire.

2015 Ford F-150 spied in the rain

Standing as quite a contrast from the spy shots of the 2015 Ford Mustang we saw earlier today, our spies also sent along these pictures of the next-generation F-150 pickup out testing in its (heavily camouflaged) full prototype body. Much of the new truck's design is hidden under the bulky coveralls, but we expect a lot of its new lines to be inspired by the Atlas concept that debuted at the 2013 Detroit Auto Show.
Perhaps the biggest unknown surrounding the new F-150 is what, exactly, its body will be made of. Earlier reports have suggested that lightweight aluminum materials may be used throughout, offering a serious reduction in weight versus previous models. But Ford engineers will need to be careful, though, as they need to keep a tight rein on costs while preserving class-competitive (if not class-leading) towing and payload capacity.
On the powertrain front, the new F-150 will undoubtedly carry on with EcoBoost engines, and we'd bet on a normally aspirated V8 as well. A diesel option hasn't been confirmed, but we wouldn't be surprised to see one some time in the truck's lifecycle. Mum's the word on when the production F-150 will be revealed, but our best guess is that we'll see it at the 2014 Detroit Auto Show.