1971 Classic Ford Bronco. on 2040-cars

Auto blog

How Ford made its 2015 Ford Mustang safer for toupee wearers [w/video]

Ford is ready to tell the story of its 2015 Mustang Convertible, the can't-miss bits being the easier, quicker and quieter roof operation, a more robust roof build for a coupe-like cabin noise, more trunk space, better visibility and reduced in-cabin buffeting. The top release system has been completely redesigned with a single, center-mounted latch on the windshield frame instead of the dual latches of before. The driver can now release the roof without having to lean over into the passenger space, after which the top goes down fully automatically with the press of a button. Ford doesn't say how long it takes to stow, but it's apparently done in half as much time as before, so figure around 8 seconds.
The roof uses a five-bow structure, with the fabric outer and full inner headliner sandwiching ten millimeters of insulation. Detailing work on the top has eliminated "unsightly folds" in the corners when the roof is up and made it more compact when down; its Z-fold assembly is 6.7 inches lower than before at its highest point when put down. Ford says the new electric drive internals make less noise when in operation, and the fully-finished droptop look is achieved with snap-in caps that flank the rear seating and stow in the trunk when not in use (the outgoing Mustang's top was higher and the front when folded and always looked like it was catching air and creating drag).
The compact roof and newly independent rear suspension setup in back means liberated trunk space, 11.4 cubic feet ready to swallow golf bags and tourist swag. You can read a lot more about it in the press release below, check it out in the short video of running footage and learn about the aerodynamic improvements made to the entire Mustang lineup that decrease drag and increase fuel economy.

Ring Brothers shows 1965-66 Mustang fastback carbon fiber body

We covered one of Ring Brothers' more extreme SEMA builds yesterday, the De Tomaso Pantera-based ADRNLN, but if that well-executed but over-the-top Italian-American exotic is too much for you, then perhaps this Ring Brothers 1965 Ford Mustang fastback with a carbon-fiber body suits your tastes better.
What the performance-parts manufacturer is showcasing with the Mustang is the carbon-fiber body itself, which is fashioned around the 1965-66 fastback. It can be bought from the company and bonded to the skin and unibody as a do-it-yourself project, or you can take your Mustang to Ring Brothers and have the body installed there. The fenders, doors and quarter panels are two-inches wider than stock, and Ring Brothers offers a custom widebody chassis to those who want the complete package.
The show car looks sharp in person lowered on HRE wheels, and we appreciate the bare front end so we can see the supercharged V8 and front coilover suspension, though the details on those performance upgrades are slim. Also note the custom independent rear suspension setup at the rear.

Lincoln Nautilus, Ford Edge latest prediction: Production ends in July 2024

In June, Auto Forecast Solutions put out a report compiled by its vice president of global forecasting, Sam Fiorani. One item in the report covered how Fiorani had heard from "multiple sources" that Ford shut down the program to replace the Edge crossover in 2023. Assuming this came to pass, with the Lincoln Nautilus based on the Edge, the inference is that the Nautilus would retire at or around the same time. Ford's response to media queries about the report was either "No comment" or PR-speak deflection. Lincoln's statement on the matter to Motor1, a crafty non-answer, was, "The Nautilus plays and will continue to play an important role in Lincoln’s growing SUV portfolio which includes the Corsair, Aviator and Navigator. Lincoln is investing in growth segments like SUVs and we have no plans to exit the segment." It's possible Lincoln has no plans to leave the segment, but the Nautilus might, according to a fresh, unsourced report in Ford Authority. The site claims the Nautilus will end production at the Oakville Assembly Plant in Ontario, Canada, in July 2024.  Again, we can't know how much, if any of this, is true. But we're zeroing in on a timeline for the potential end of the Edge and Nautilus in the U.S. Those are the only two products Oakville currently builds, and when the Canadian union Unifor asked Ford about the reports in June, Ford couldn't offer union reps anything concrete or reassuring. The Detroit News quoted Unifor chief Jerry Dias as saying of the automaker, "There is no question, they are going through a major evaluation of their portfolio, based on a whole host of things."   We could be seeing one of the earlier theories for Edge's potential demise coming true. Some analysts suspect Ford could be pruning its crossover lineup because it has too many similarly-sized offerings at the moment, the Edge hasn't met its sales targets in Europe, and more compact crossovers are on the way that could bring better street cred if they're associated with the Bronco or Bronco Sport. Unifor and Ford are now in negotiations over a new contract, so it's possible we'll get more clarity in the next month or so about Ford's plans and what will come of Oakville and its roughly 4,000 workers. If Ford walks away from the assembly plant, it will only have two engine plants left in Canada, and no vehicle assembly north of the border for the first time in about a century.