1989 Ford Mustang Gt Convertible on 2040-cars

Auto blog

Aluminum lightweighting does, in fact, save fuel

When the best-selling US truck sheds the equivalent weight of three football fullbacks by shifting to aluminum, folks start paying attention. Oak Ridge National Laboratory took a closer look at whether the reduced fuel consumption from a lighter aluminum body makes up for the fact that producing aluminum is far more energy intensive than steel. And the results of the study are pretty encouraging. In a nutshell, the energy needed to produce a vehicle's raw materials accounts for about 10 percent of a typical vehicle's carbon footprint during its total lifecycle, and that number is up from six percent because of advancements in fuel economy (fuel use is down to about 68 percent of total emissions from about 75 percent). Still, even with that higher material-extraction share, the fuel-efficiency gains from aluminum compared to steel will offset the additional vehicle-extraction energy in just 12,000 miles of driving, according to the study. That means that, from an environmental standpoint, aluminum vehicles are playing with the house's money after just one year on the road. Aluminum-sheet construction got topical real quickly earlier this year when Ford said the 2015 F-150 pickup truck would go to a 93-percent aluminum body construction. In addition to aluminum being less corrosive than steel, that change caused the F-150 to shed 700 pounds from its curb weight. And it looks like the Explorer and Expedition SUVs may go on an aluminum diet next. Take a look at SAE International's synopsis of the Oak Ridge Lab's study below. Life Cycle Energy and Environmental Assessment of Aluminum-Intensive Vehicle Design Advanced lightweight materials are increasingly being incorporated into new vehicle designs by automakers to enhance performance and assist in complying with increasing requirements of corporate average fuel economy standards. To assess the primary energy and carbon dioxide equivalent (CO2e) implications of vehicle designs utilizing these materials, this study examines the potential life cycle impacts of two lightweight material alternative vehicle designs, i.e., steel and aluminum of a typical passenger vehicle operated today in North America. LCA for three common alternative lightweight vehicle designs are evaluated: current production ("Baseline"), an advanced high strength steel and aluminum design ("LWSV"), and an aluminum-intensive design (AIV).

McLaren, Koenigsegg, Toyota, Ford, Dodge and Corvette Lego kits announced for 2021

Lego has announced a slew of car-themed sets for 2021. The six kits comprise nine vehicles and fall under the brick pusher's Speed Champion line of official OEM-licensed kits. News of their arrival comes from German toy retailer JB Spielwaren's pre-order listings, which show three single-car sets and three dual-car sets of matched marques. Starting with the McLaren Elva roadster, the kit consists of 263 pieces and is finished in blue. It seems to have a difficult time capturing the curves of the real-life Elva, but there's only so much you can do with a bunch of plastic blocks. Lego has made several other McLaren kits before, including the Senna, 720S, and a more advanced Senna GTR for the Technics line. Next up is the Koenigsegg Jesko, made up of 280 pieces and finished in white. Though the real-life Jesko is still curvy, this kit does a better job of replicating its aggressive maw, vents and cantilevered rear wing. Rounding out the single-car sets is the 299-piece Toyota GR Supra in yellow. This marks the first time Toyota has lent their license to Lego. Again, it struggles a bit to represent the curvy Supra, relying on printed details like logos and headlights to identify. On the other hand, the Chevrolet two-car does a stupendous job with the 1968 Corvette. The C3 is instantly recognizable as such. The C8-R race car it's paired with suffers from the same issues as some of the previous cars, though. The set contains 512 pieces, and funnily enough the C8 driver has short hair while the C3 driver sports a period-correct wavy mane. The next set is a 627-piece Mopar-themed pair, including a purple (Plum Crazy?) 1970 Dodge Challenger T/A and an SRT top fuel dragster. The race car is spot on, but the Challenger was probably tough to make given the width restrictions. It looks a couple of pegs too narrow compared to the wide proportions of the real deal. Last but not least, the Ford set contains a Bronco R and Ford GT Heritage Edition. Consisting of 660 pieces, the set does an excellent job of representing both cars. The GT looks faithful in its Gulf livery, and the Bronco R looks more like a real Bronco than the actual Bronco R race truck. All in all, it's always fun to see more Lego sets with real cars, and we're glad to see more manufacturers added to the roster. The single-car sets are recommended for ages 7 and up, while the double-car sets have an 8 years and up rating. Price in U.S.

Submit your questions for Autoblog Podcast #321 LIVE!

We're set to record Autoblog Podcast #321 tonight, and you can drop us your questions and comments regarding the rest of the week's news via our Q&A module below. Subscribe to the Autoblog Podcast in iTunes if you haven't already done so, and if you want to take it all in live, tune in to our UStream (audio only) channel at 10:00 PM Eastern tonight.
Discussion Topics for Autoblog Podcast Episode #321
Unibody Ford Ranger replacement