1979 Ford Granada on 2040-cars

Auto blog

Aluminum lightweighting does, in fact, save fuel

When the best-selling US truck sheds the equivalent weight of three football fullbacks by shifting to aluminum, folks start paying attention. Oak Ridge National Laboratory took a closer look at whether the reduced fuel consumption from a lighter aluminum body makes up for the fact that producing aluminum is far more energy intensive than steel. And the results of the study are pretty encouraging. In a nutshell, the energy needed to produce a vehicle's raw materials accounts for about 10 percent of a typical vehicle's carbon footprint during its total lifecycle, and that number is up from six percent because of advancements in fuel economy (fuel use is down to about 68 percent of total emissions from about 75 percent). Still, even with that higher material-extraction share, the fuel-efficiency gains from aluminum compared to steel will offset the additional vehicle-extraction energy in just 12,000 miles of driving, according to the study. That means that, from an environmental standpoint, aluminum vehicles are playing with the house's money after just one year on the road. Aluminum-sheet construction got topical real quickly earlier this year when Ford said the 2015 F-150 pickup truck would go to a 93-percent aluminum body construction. In addition to aluminum being less corrosive than steel, that change caused the F-150 to shed 700 pounds from its curb weight. And it looks like the Explorer and Expedition SUVs may go on an aluminum diet next. Take a look at SAE International's synopsis of the Oak Ridge Lab's study below. Life Cycle Energy and Environmental Assessment of Aluminum-Intensive Vehicle Design Advanced lightweight materials are increasingly being incorporated into new vehicle designs by automakers to enhance performance and assist in complying with increasing requirements of corporate average fuel economy standards. To assess the primary energy and carbon dioxide equivalent (CO2e) implications of vehicle designs utilizing these materials, this study examines the potential life cycle impacts of two lightweight material alternative vehicle designs, i.e., steel and aluminum of a typical passenger vehicle operated today in North America. LCA for three common alternative lightweight vehicle designs are evaluated: current production ("Baseline"), an advanced high strength steel and aluminum design ("LWSV"), and an aluminum-intensive design (AIV).

2015 Ford Mustang leaked in Autoweek

We would have to imagine that Ford knew it couldn't keep its 2015 Mustang under wraps for too long, and with only days to go before the pony car's official unveiling, the dam seems to be cracking. SVTPerformance.com member Screamin 40th just posted some images taken of the sixth-gen Mustang prominently featured in and on the cover of the December 9 issue of Autoweek magazine.
These images show that recent renderings we saw weren't too far off. The face is just like what we saw in spy shots a few months back, but the rear of the car features some of its more striking cues. Starting with the pronounced haunches and hidden B-pillars, the rear view of the new Mustang might be its best with the ridged, three-bar taillights, a rear diffuser and the lack of a faux gas cap, which allows the galloping pony to be an even more prominent element against the black trim.
The images also reveal a small portion of the updated interior carrying over retro themes like the deep-dish steering wheel and dual-gauge instrument cluster, but it also adds some modern tech with a big infotainment displays and a clean center stack layout. No official word on powertrain or other specs, but while we can't make out most of the magazine's text, our eyes did catch mentions of an independent rear suspension and a 200-pound weight reduction.

Black Zombie electric Mustang launches Blood Shed Motors [w/videos]

As patient zero of Blood Shed Motors, the classic pony car has received a powerful electric transplant. Lightning repeatedly vanquished the darkness like the angriest of strobe lights and thunder shook the building, punctuating the clatter of a heavy Texas rain on the metal roof as the clock ticked away the initial seconds of a rare full moon Friday the 13th. It was then that the Black Zombie came to life for the first time. Beneath the hood of this rust-free 1968 Mustang fastback, a 289-cubic-inch V8 no longer turns gasoline into heat, noise and pollution. As patient zero of Blood Shed Motors, the classic pony car has received a powerful electric transplant, and now boasts twinned Warp 11 DC motors and a pair of fresh Zilla controllers that will serve as the basic blueprint for future vehicles. Dubbed the Zombie 222 drivetrain, the setup will be limited to 750 horsepower in customer's cars to keep the maintenance experience low, and eventually will draw power from a 40-kWh battery pack. In this first example, though, the output is bit more extreme. For one day, at least, they have the 1,500-kW-capable pack that powers the record-setting Swamp Rat 37 racer belonging to Don Garlits and a brief window of opportunity to try it out on a track. Blood Shed Motors is the result of a collaboration between NEDRA co-founder John "Plasma Boy" Wayland, the man who helped bring electric vehicle drag racing to the attention of the world with his unassuming White Zombie Datsun 1200 conversion and Austin, TX business man Mitch Medford, who've put together a small team of experts in their chosen fields. The plan is to build a limited number of muscle car conversions on pristine early Mustang, Camaro, and Barracuda platforms. The plan is to build a limited number of high-quality muscle car conversions on pristine (No restored rust buckets!) early Mustang, Camaro, and Barracuda platforms. Each can be customized according to buyer's wishes and blessed with its own serial number. The price tags will be in the eye-watering $200,000-and-up neighborhood, reflective of the cost and rarity of these cars and the custom nature of the alterations. Of course, you can't just multiply horsepower and add the monster torque that these electric motors put out and expect an antique chassis to hold up.