Ford > Galaxie

1966 Ford Galaxie Ltd on 2040-cars

Year:1966 Mileage:94000 Color: White /
Green

Location:

Lenoir, North Carolina, United States

Transmission:Automatic
Body Type:Coupe
Vehicle Title:Clear
Engine:390
Fuel Type:Gasoline
For Sale By:Private Seller

Condition:
Used: A vehicle is considered used if it has been registered and issued a title. Used vehicles have had at least one previous owner. The condition of the exterior, interior and engine can vary depending on the vehicle's history. See the seller's listing for full details and description of any imperfections. ...
VIN (Vehicle Identification Number): 00000000000
Year: 1966
Number of Cylinders: 8
Make: Ford
Model: Galaxie
Trim: LTD
Power Options: Air Conditioning
Drive Type: 2
Mileage: 94,000
Sub Model: LTD
Disability Equipped: No
Exterior Color: White
Warranty: Vehicle does NOT have an existing warranty
Interior Color: Green

Up for sale is my 1966 ford LTD. This ford has some unusual options. It has PS,PB,AC, four way flashers, factory power disc brakes, and a 390 engine with factory four barrel carb. I found it through word of mouth from a friend of a friend. It had been bought by and older gentleman many years ago and had been setting in a shed for years. I believe the last inspection was 1978. It has a super body for it's age. The only rust I saw was underneath the lip of the hood and a couple of very small spots on the lower doors. I've seen very few of these LTD 2 doors with the 390 engine and even fewer with factory disc brakes and A/C.It came out factory with a vinyl top but someone had the foresight to remove it long ago before it had a chance to start rusting. I'll tell you the good and the bad. The good: It has new water pump, new belts, rebuilt four barrel carb, new master cylinder, new read wheel cylinders, rebuilt front calipers, and a new starter. The bad: I needs a heater core and one cylinder is low on compression. I believe it has carbon under the valve because the lifter is moving as it should and all the other cylinder have good compression. I believe just about all the lights work and it stops and drive good. The interior is good but faded badly. I have a clear title in my name. You welcome to call or e-mail. Thanks for bidding. 828 781 7530

Ford Galaxie for Sale

Auto Services in North Carolina

Window Genie ★★★★★

Auto Repair & Service, Window Tinting, Pressure Washing Equipment & Services

Address: 5300 Atlantic Ave, Raleigh

Phone: (919) 745-8048

West Lee St Tire And Automotive Service Center Inc ★★★★★

Auto Repair & Service

Address: 1100 W Lee St, Oak-Ridge

Phone: (336) 272-8616

Upstate Auto and Truck Repair ★★★★★

Auto Repair & Service, Automobile Diagnostic Service

Address: 2040 Victory Trail Rd, Earl

Phone: (864) 487-9272

United Transmissions Inc ★★★★★

Auto Repair & Service, Auto Transmission, Towing

Address: 2615 Battleground Ave, Summerfield

Phone: (336) 288-3317

Total Collision Repair Inc ★★★★★

Automobile Body Repairing & Painting

Address: 413 Chatham St, Mamers

Phone: (919) 774-7509

Supreme Lube & Svc Ctr ★★★★★

Auto Repair & Service, Auto Oil & Lube, Automobile Inspection Stations & Services

Address: 13715 Nc 50 Hwy N, Benson

Phone: (919) 207-0085

Auto blog

Ford to rebrand SVT as 999?

Mon, 22 Sep 2014

Ford operates a number of performance divisions around the world. There's SVT in the US, Team RS in Europe and Ford Performance Vehicles (FPV) in Australia. But the Blue Oval has been steadily integrating its performance operations into one unit, and here we might have our first indication of what it will be called.
A reader at Jalopnik sent in a survey in which respondents were asked to gauge the name for a new performance brand from a "major automotive manufacturer," and while the identity of that automaker was not disclosed, according to the survey, the automaker is considering the name 999 for its new go-fast unit.
As our compatriots point out, the 999 was Ford's first racecar, a rudimentary chassis with a 19-liter inline-four campaigned by Henry Ford around the turn of the 20th century. (Ford also used the number to designate a Fusion fuel-cell racer a few years back.) That could prove the tie-in Dearborn is looking for in rebranding its performance operations worldwide, replacing the letters SVT, RS and FPV globally under one name.

Top Gear pits Hennessey VelociRaptor vs. Range Rover Sport SVR

Fri, Jun 5 2015

As a television series, Top Gear is in limbo with an intent to return, but no hosts yet. However, it's magazine and website continue to bring us clips like this one. While the video might lack the show's charismatic hosts, this is an opportunity to see a drag race between a Land Rover Range Rover Sport SVR with 550 horsepower and a Hennessey VelociRaptor with 623 hp. The duel between these two supercharged V8s definitely sounds great. Both rugged models start at the line growling angrily at each other like dogs ready for a fight. You have to watch the clip to see whether the more powerful VelociRaptor feeds on the SVR, though. News Source: Top Gear via YouTube Ford Land Rover Truck SUV Performance Videos Hennessey ford f-150 svt raptor top gear magazine

Ford 3D-printing Mustang out of chocolate and candy for Valentine's Day

Thu, 13 Feb 2014

Is your beloved in love with the new 2015 Ford Mustang? Do they like chocolate (that's a trick question - everyone likes chocolate)? Are they a bit of a futurist? Then this Hallmark holiday, you need to get them this Ford Mustang, 3D-printed in sweet, delicious chocolate.
Ford is teaming with 3D Systems' Sugar Lab in LA to produce the super-accurate pony car confections in both chocolate and sugar candy varieties. The process kicked off with a CAD rendering of the 2015 Mustang, which was then programmed into the 3D printer. After a bit of work from the machine, a four-inch long, two-inch tall Mustang was the result. Why the tieup with 3D Systems, though?
"We wanted to create something fun to show that while 3D printing made these edible Mustangs, manufacturing-level 3D printing was used in the development of Ford's all-new sports car," said Paul Susalla, Ford's supervisor of 3D printing.