2014 Ford Focus Se on 2040-cars

Auto blog

Ford recalls 9,900 vehicles across two campaigns

Ford is recalling a total of 9,885 vehicles in two campaigns. The Basics: In one recall, Ford will recall 9,017 examples of the 2013 Escape with build dates from January 11, 2012, to April 1, 2013, and the 2013-2014 Focus ST produced between May 3, 2012, and October 14, 2013. The Problem: Splices in the engine wiring harness might not have enough compression, and this can cause the manifold absolute pressure sensor to send incorrect signals to the powertrain control module. This issue could cause the engine to stall. Injuries/Deaths: None reported. The Fix: Dealers will replace the current crimped splices with new splices, according to the National Highway Traffic Safety Administration. If You Own One: The repair campaign will begin on January 4, 2016. More Information: Ford recalled the 2013 Escape and Focus ST in August 2014 for the same problem, and this is an expansion of that campaign, according to company spokesperson John Cangany to Autoblog. The Basics: In the smaller of the two campaigns, Ford will recall 868 examples of the 2013 Explorer, Explorer Police Utility, Taurus, Taurus Police Interceptor, Flex, Lincoln MKS, and MKT. The Problem: The fuel delivery module can crack, which would cause a fuel leak. Injuries/Deaths: None reported. The Fix: Dealers will replace the fuel delivery module. If You Own One: Owners should receive notice soon because NHTSA's report says the recall begins in December. More Information: According to Cangany, this recall is an expansion of a campaign from 2013 for these vehicles. RECALL Subject : Engine Wiring Splices may cause Stall Report Receipt Date: DEC 02, 2015 NHTSA Campaign Number: 15V813000 Component(s): ELECTRICAL SYSTEM Potential Number of Units Affected: 9,017 All Products Associated with this Recall Vehicle Make Model Model Year(s) FORD ESCAPE 2013 FORD FOCUS 2013-2014 Details Manufacturer: Ford Motor Company SUMMARY: Ford Motor Company (Ford) is recalling certain model year 2013 Escape vehicles manufactured January 11, 2012, to April 1, 2013, and 2013-2014 Focus ST vehicles manufactured May 03, 2012, to October 14, 2013. Insufficient compression in the engine wiring harness splices to the Manifold Absolute Pressure (MAP) sensor may provide incorrect signals to the powertrain control module (PCM). CONSEQUENCE: The incorrect signals could cause the vehicle to hesitate or the engine to stall, increasing the risk of a crash.

2015 Ford Mustang already under recall, but just 53 units

Ford has issued a small - but significant - recall for one of its spotlight cars: the 2015 Mustang.
The recall affects just 53 cars, with 50 in the United States and three in Canada. Ford said the passenger side safety belt buckle tension sensor may not have been calibrated properly by the supplier. This could lead to "misclassification" of the passenger seat occupant, and could cause the airbag to deploy improperly.
A Ford spokesperson didn't immediately respond to a request for comment. In a statement, the automaker said it is not aware of any accidents or injuries, and dealers will replace the buckle assembly at no cost to customers. The cars affected were built at Flat Rock Assembly Plant in Michigan from Aug. 18 to Oct. 2.

Ford cleans up painting process with cameras

Knowing how the bacon gets made rarely entices us and, in the same vein, the same usually goes for knowing about how new cars get painted. But in both instances, however, quality - or a lack thereof - is instantly obvious. In terms of the latter, Ford is showing off its new paint quality process with 3D Dirt Detection Technology to find imperfections in vehicle paint more easily and more quickly.
This process - being performed on the F-150 SVT Raptor above - uses 16 computer-controlled cameras to create a three-dimensional model (inset) of the vehicle to detect flaws in the paint including dirt particles, which can then be buffed out manually. Ford says this new technology cuts down on time spent looking for paint flaws and gives workers more time to correct those that are discovered.
Currently, Ford only uses its 3D Dirt Detection Technology system at three factories (the Dearborn, MI facility, along with those in Louisville, Kentucky and Valencia, Spain), but it will soon spread to five more plants in North America. Ford has released a video and press release for this innovative and unexpectedly interesting process, both of which are posted below.