2003 Ford Zx3 Base on 2040-cars

Auto blog

Aluminum lightweighting does, in fact, save fuel

When the best-selling US truck sheds the equivalent weight of three football fullbacks by shifting to aluminum, folks start paying attention. Oak Ridge National Laboratory took a closer look at whether the reduced fuel consumption from a lighter aluminum body makes up for the fact that producing aluminum is far more energy intensive than steel. And the results of the study are pretty encouraging. In a nutshell, the energy needed to produce a vehicle's raw materials accounts for about 10 percent of a typical vehicle's carbon footprint during its total lifecycle, and that number is up from six percent because of advancements in fuel economy (fuel use is down to about 68 percent of total emissions from about 75 percent). Still, even with that higher material-extraction share, the fuel-efficiency gains from aluminum compared to steel will offset the additional vehicle-extraction energy in just 12,000 miles of driving, according to the study. That means that, from an environmental standpoint, aluminum vehicles are playing with the house's money after just one year on the road. Aluminum-sheet construction got topical real quickly earlier this year when Ford said the 2015 F-150 pickup truck would go to a 93-percent aluminum body construction. In addition to aluminum being less corrosive than steel, that change caused the F-150 to shed 700 pounds from its curb weight. And it looks like the Explorer and Expedition SUVs may go on an aluminum diet next. Take a look at SAE International's synopsis of the Oak Ridge Lab's study below. Life Cycle Energy and Environmental Assessment of Aluminum-Intensive Vehicle Design Advanced lightweight materials are increasingly being incorporated into new vehicle designs by automakers to enhance performance and assist in complying with increasing requirements of corporate average fuel economy standards. To assess the primary energy and carbon dioxide equivalent (CO2e) implications of vehicle designs utilizing these materials, this study examines the potential life cycle impacts of two lightweight material alternative vehicle designs, i.e., steel and aluminum of a typical passenger vehicle operated today in North America. LCA for three common alternative lightweight vehicle designs are evaluated: current production ("Baseline"), an advanced high strength steel and aluminum design ("LWSV"), and an aluminum-intensive design (AIV).

XCAR stages epic drag race between Ford GT40, GT70 and GT

XCAR has put together what it believes is a first - a drag race between Ford's legendary, Le Mans-winning GT40, the more recent GT supercar it inspired and the little-known GT70 rally car. The three mid-engined monsters were all built for very different purposes, and not surprisingly, they come to battle with very different powertrains.
The GT40 is powered by a thumping, naturally aspirated V8. This example, which looks like a Mark IV model, is likely powered by a 7.0-liter engine, although it's not entirely clear how much power it's putting down. The GT70, meanwhile, was Ford's response to the Lancia Stratos. Considering that the Lancia is one of the greatest rally cars in history and many of you are probably just hearing of the GT70 for the first time, you can imagine how much success Ford had with it. Only six were produced before a change in regulations doomed this mid-engined rally car.
The Ford GT, meanwhile, doesn't really need an introduction. 550 horsepower is on offer from a 5.4-liter, supercharged V8, which keeps the GT competitive even against more modern supercars. 60 miles per hour arrives in well under four seconds while the top speed sits at 212 mph. Not bad for a car that went out of production in 2006.

NHTSA upgrades Ford floor mat unintended acceleration probe

According to a Bloomberg report, the National Highway Traffic Safety Administration has upgraded an investigation into complaints of unintended acceleration lodged against Ford vehicles. The investigation began in June of 2010 when just three complaints had been received and it only concerned the Ford Fusion and Mercury Milan, but this was at a time when the phrase "unintended acceleration" made grown men go pale. With 49 additional complaints received since then, the investigation has been reclassified as an engineering analysis - the last phase before a recall - and it has been expanded to include the Lincoln MKZ, making for a total of "around 480,000" units affected between the three sedans from the 2008 to 2010 model years.
The ostensible cause is that floor mats are trapping the accelerator pedal, but according to a Ford statement at the time, the entrapment is due to owners placing the optional all-weather floor mats, or aftermarket floor mats, on top of the car's standard floor mats. NHTSA has backed up that assessment, pinning the blame on "unsecured or double stacked floor mats."
On the face of it, it would appear that NHTSA has upgraded the status not because of Ford's error, but owner error, and Ford has stated publicly that it is "disappointed" in NHTSA's move. On top of NHTSA still being skittish after that other unintended acceleration debacle, it could be seen to be taking its time investigating all of the variables: it's reported that Ford changed its accelerator pedal design in 2010, a "heel blocker" in the floorpan has been considered a potential culprit in how the floor mats could be trapping the pedal, some drivers have said the floor mats weren't anywhere near the pedal, and according to a report in the LA Times, in "a letter sent by Ford to NHTSA in August 2010, the automaker said it found three injuries and one fatality that 'may have resulted from the alleged defect.'"