Md Inspected 2002 Ford F350 Superduty 4x4 Supercab Xlt - 6" Lift - Pickup Truck on 2040-cars

Auto blog

eBay Find Of The Day: 1988 Saleen Ford Mustang General Tire 21R race car

Saleen may be making headlines these days for working on the Tesla Model S, but its history and bread-and-butter is all about the Ford Mustang. The rear-wheel-drive Dearborn pony cars singlehandedly put the company on the map in the '80s. Founder Steve Saleen was already a talented American racing driver when he started the venture, and like many auto industry businesses before him, Saleen went to the track to prove his vehicles' worth. Now, there's a chance to buy one of those early racers on eBay Motors.
Saleen Mustangs raced in the Sports Car Club of America Escort Endurance Championship - a series of multi-hour races meant to challenge man and machine. Ostensibly a showroom stock class, the cars had larger wheels, tuned suspensions and other upgrades that stretched the concept slightly. Saleen found major success though, taking the championship for its class in 1987 and winning the 24 Hours of Mosport consecutively from 1986 through 1988.
According to the seller, Saleen only built eight of these cars, and this one carries the #21R serial number. They all started life as new Mustangs from Ford dealers but were immediately stripped and prepped to go racing. Beyond obvious mods like a roll cage, they featured eight-inch wide wheels in front, an inch of additional track width, stiffer suspension bushings and much more.

NHTSA upgrades Ford floor mat unintended acceleration probe

According to a Bloomberg report, the National Highway Traffic Safety Administration has upgraded an investigation into complaints of unintended acceleration lodged against Ford vehicles. The investigation began in June of 2010 when just three complaints had been received and it only concerned the Ford Fusion and Mercury Milan, but this was at a time when the phrase "unintended acceleration" made grown men go pale. With 49 additional complaints received since then, the investigation has been reclassified as an engineering analysis - the last phase before a recall - and it has been expanded to include the Lincoln MKZ, making for a total of "around 480,000" units affected between the three sedans from the 2008 to 2010 model years.
The ostensible cause is that floor mats are trapping the accelerator pedal, but according to a Ford statement at the time, the entrapment is due to owners placing the optional all-weather floor mats, or aftermarket floor mats, on top of the car's standard floor mats. NHTSA has backed up that assessment, pinning the blame on "unsecured or double stacked floor mats."
On the face of it, it would appear that NHTSA has upgraded the status not because of Ford's error, but owner error, and Ford has stated publicly that it is "disappointed" in NHTSA's move. On top of NHTSA still being skittish after that other unintended acceleration debacle, it could be seen to be taking its time investigating all of the variables: it's reported that Ford changed its accelerator pedal design in 2010, a "heel blocker" in the floorpan has been considered a potential culprit in how the floor mats could be trapping the pedal, some drivers have said the floor mats weren't anywhere near the pedal, and according to a report in the LA Times, in "a letter sent by Ford to NHTSA in August 2010, the automaker said it found three injuries and one fatality that 'may have resulted from the alleged defect.'"

Ford 3D-printing Mustang out of chocolate and candy for Valentine's Day

Is your beloved in love with the new 2015 Ford Mustang? Do they like chocolate (that's a trick question - everyone likes chocolate)? Are they a bit of a futurist? Then this Hallmark holiday, you need to get them this Ford Mustang, 3D-printed in sweet, delicious chocolate.
Ford is teaming with 3D Systems' Sugar Lab in LA to produce the super-accurate pony car confections in both chocolate and sugar candy varieties. The process kicked off with a CAD rendering of the 2015 Mustang, which was then programmed into the 3D printer. After a bit of work from the machine, a four-inch long, two-inch tall Mustang was the result. Why the tieup with 3D Systems, though?
"We wanted to create something fun to show that while 3D printing made these edible Mustangs, manufacturing-level 3D printing was used in the development of Ford's all-new sports car," said Paul Susalla, Ford's supervisor of 3D printing.