2015 Ford F350 on 2040-cars

Auto blog

UK's Loughborough University improving Ford's 1.0-litre EcoBoost engine

How much does it cost for college students to study zero emissions vehicles? At Loughborough University in the UK, a new Advanced Propulsion Centre (APC) is being built at a cost of a billion pounds ($1.7 billion US). The school has just announce that it will fund a number of grad student positions and is creating a new Chair in Advanced Propulsion Systems, which sounds like a fun job to us. We're weird like that. There will be a total of four professor-type positions in the new Center, including the chair, all focused on teaching students about low-carbon vehicle technologies, specifically electric and hybrid ones. The school is investing 1.5 million pounds ($2.5 million) for the new positions. There is a bigger picture as well, a 26-million pound ($44 million) Advanced Combustion Turbocharged Integrated Variable-valvetrain Engine (ACTIVE) project, which uses funds not only from the school but also from Ford and others. The point of ACTIVE is to study Ford's 1.0-liter EcoBoost engine and "improve further its efficiency and ensure it exceeds 2020 emission regulations." This is already a popular engine for the automaker, and it will need to stay at the bleeding edge of efficiency to remain as important in 2020 as it is today. Loughborough University has been working with automakers on advanced energy technologies for years, for example with Rolls-Royce and fuel cells in 2007 and the Lotus Hotfire engine in 2008. University invests GBP1.5M in advanced propulsion research to advance zero emissions vehicles challenge Loughborough University is investing GBP1.5M over five years in strategic research appointments, inspired by the global challenge to develop the new advanced propulsion technologies required for the move to zero emission vehicles. These appointments reinforce the University's world-class research in low-carbon vehicle technologies, adding new dimensions concerned with electric and hybrid drives. Four appointments will be made, including a Chair in Advanced Propulsion Systems, supported by a number of PhD studentships. The GBP1.5M investment is part of the University's commitment to the recently announced Advanced Propulsion Centre (APC) to support the development of new supply chains for low carbon vehicles. APC is an initiative established by the Automotive Council that will see GBP1 billion of investment from government and industry over the next 10 years.

Ford issues six recalls covering 101,000 vehicles for multiple issues

Ford is announcing six separate recalls for a variety of issues affecting a dozen models and a total of 100,610 vehicles in North America. However, according to Ford spokesperson Kelli Felker, "None of them have caused accidents or injuries." Half of them cover fewer than 1,000 cars.
The largest recall covers 92,022 North American examples (about 83,250 in the US) of some models of the Ford Taurus, Lincoln MKS, Ford Interceptor, Flex and Lincoln MKT from the 2013 and 2014 model years; the 2012-2014 Edge and the 2014 Lincoln MKX. All of them have a potential issue with the halfshaft on the right side that might not be fully seated and could move outward over time. If it shifts too far, the models may no longer be able to drive, and the condition could also allow the vehicles to roll away, even when in Park. Dealers will inspect the shaft to make sure it's seated and will replace the part if necessary.
The next-largest recall covers 5,264 North American examples (4,867 in the US) of the Ford F59 Commercial Stripped Chassis from the 2011-2014 model years. It's possible that an electrical junction box can corrode in areas with salty roads and short circuit. The problem could potentially cause a fire. Dealers will replace the box with an improved design.

Ford rethinking vehicle launch strategy

With a new boss at the helm, Ford is looking at new ways to improve its vehicle launches in North America to prevent recent issues that have popped up with models like the Lincoln MKZ, Ford Escape and Ford Fusion. Speaking with Automotive News, Ford's new president of the Americas, Joe Hinrichs, revealed a few ways the automaker plans to avoid early build issues such as the engine fires on certain 2013 Escape and Fusion models and months-long delays for customers to receive their MKZs.
It sounds like the root of the problems may have been Ford's relationship with suppliers compounded by the fact that the product surge came on the heels of the recent industry-crippling recession, and in the AN article, Hinrichs says improvements are being made to reduce problems during the launch of new or redesigned models. Three such improvements that were implemented during the first quarter of this year including more rigorous quality comparisons, better use of computer technology to catch major problems sooner and hiring engineers to work closer with suppliers.