Sweet 2005 Ford F-250 Super Crew Lariat Fx4 Lifted Tonneau Cover Tow Pkg on 2040-cars

Auto blog

Ford paying $750 million just to close plant in Belgium

According to a report from Reuters, Ford is shelling out $750 million in a severance deal that will see the automaker close its facility in Genk, Belgium. The automaker reached this deal with the 4,000 hourly workers employed at the plant last week, which means the company will pay out an average of $187,500 per worker.
Ford is still negotiating with the 300 salaried workers at the factory, which currently produces the Mondeo sedan. All told, Ford expects to lose around $2 billion in Europe thanks in no small part to the region's ongoing economic downturn, and two more plants are scheduled to be shut down in Europe this year. The company will log its $750 million payout under "special items" for this quarter.
As you may recall, Ford took a similar path in the US back in 2009 when the domestic market took a spill. Back then, the company shelled out around $50,000 per employee with at least one year of experience, plus either $25,000 toward a new car or an extra cash payment of $20,000. It would seem the cost of closing plants in Belgium is a much harder pill to swallow than in the States...

Ford recalling 2015 Mustang for fuel line leak, 20K Transit Connects for plastic panel

Ford is recalling 738 examples of the 2015 2015 Mustang with the 2.3-liter EcoBoost engine – 712 in the US, 16 in Canada. A fuel pressure sensor might have been installed incorrectly on the affected cars, and that could result in a fuel leak. At the time of writing the company hasn't heard any reports of any incidents related to the issue, and parties with affected vehicles can take them to the dealer to have the fuel tube assembly replaced free of charge. The 2014 Transit Connect Cargo Van is also the subject of a safety recall, due to a possible problem with adhesive used on the exterior plastic panel on the sliding doors. There are 19,825 units covered by that recall, which dealers will also repair free of charge. You can find more information on both bulletins in the press releases below. Ford Issues Safety Recall for Certain 2015 Mustang Vehicles in North America for Fuel Pressure Sensor Issue Dec 4, 2014 | DEARBORN, Mich. - Ford is issuing a safety recall for approximately 730 2015 Ford Mustang vehicles in North America (actual 728) for a potential fuel line leak. A fuel pressure sensor, which is part of the fuel supply tube assembly, may have been installed incorrectly, potentially resulting in a pressurized fuel leak. A fuel leak in the presence of an ignition source may result in a fire. Ford is not aware of any fires, accidents or injuries related to this condition. Affected vehicles include certain 2015 Ford Mustangs equipped with 2.3-liter engines built at Flat Rock Assembly Plant, Sept. 25, 2014 to Oct. 9, 2014. Ford is aware of 712 vehicles in the United States and federalized territories and 16 in Canada. These totals are as of Dec. 3, 2014. Dealers will replace the fuel supply tube assembly at no cost to the customer. *** Ford Issues Safety Recall for Certain 2014 Transit Connect Cargo Van Vehicles in North America for Issue with the Plastic Panel on the Sliding Doors Dec 4, 2014 | DEARBORN, Mich. - Ford is issuing a safety recall for approximately 20,000 2014 Transit Connect cargo van vehicles in North America (actual 19,825) for an issue with adhesion of an exterior plastic panel to the sliding doors. This issue may result in noise, a water leak, a loose panel, or separation of the plastic panel from the vehicle while driving, potentially increasing the risk of an accident or injury. Ford is not aware of any accidents or injuries related to this condition.

Aluminum lightweighting does, in fact, save fuel

When the best-selling US truck sheds the equivalent weight of three football fullbacks by shifting to aluminum, folks start paying attention. Oak Ridge National Laboratory took a closer look at whether the reduced fuel consumption from a lighter aluminum body makes up for the fact that producing aluminum is far more energy intensive than steel. And the results of the study are pretty encouraging. In a nutshell, the energy needed to produce a vehicle's raw materials accounts for about 10 percent of a typical vehicle's carbon footprint during its total lifecycle, and that number is up from six percent because of advancements in fuel economy (fuel use is down to about 68 percent of total emissions from about 75 percent). Still, even with that higher material-extraction share, the fuel-efficiency gains from aluminum compared to steel will offset the additional vehicle-extraction energy in just 12,000 miles of driving, according to the study. That means that, from an environmental standpoint, aluminum vehicles are playing with the house's money after just one year on the road. Aluminum-sheet construction got topical real quickly earlier this year when Ford said the 2015 F-150 pickup truck would go to a 93-percent aluminum body construction. In addition to aluminum being less corrosive than steel, that change caused the F-150 to shed 700 pounds from its curb weight. And it looks like the Explorer and Expedition SUVs may go on an aluminum diet next. Take a look at SAE International's synopsis of the Oak Ridge Lab's study below. Life Cycle Energy and Environmental Assessment of Aluminum-Intensive Vehicle Design Advanced lightweight materials are increasingly being incorporated into new vehicle designs by automakers to enhance performance and assist in complying with increasing requirements of corporate average fuel economy standards. To assess the primary energy and carbon dioxide equivalent (CO2e) implications of vehicle designs utilizing these materials, this study examines the potential life cycle impacts of two lightweight material alternative vehicle designs, i.e., steel and aluminum of a typical passenger vehicle operated today in North America. LCA for three common alternative lightweight vehicle designs are evaluated: current production ("Baseline"), an advanced high strength steel and aluminum design ("LWSV"), and an aluminum-intensive design (AIV).