1968 Ford F100 ***5.9l 6bt 12v Cummins Swap*** on 2040-cars

Auto blog

Toyota fears supplier pressure in Australia with GM pull out

With Ford and General Motors both announcing an end to production in Australia, the country's auto industry is in a bad way. With the exit of two big players, there's increased concern that a third Australian manufacturer, Toyota, will be forced out, as well.
"We are saddened to learn of GM Holden's decision. This will place unprecedented pressure on the local supplier network and our ability to build cars in Australia," Toyota Australia said in a statement. The GM closure of Holden production will be the direct end to 2,900 jobs, but will also force a dramatic reduction in the size of the country's supplier network, as there will simply be fewer cars to build.
In the same statement, Toyota Australia said it would work with suppliers and local government to figure out whether continuing production Down Under was even feasible. According to Automotive News, a representative for the Australian Manufacturing Workers' Union told reporters it was "highly likely" that Toyota would also close up shop within the next few years.

Volkswagen could outsell GM in China for the first time in nine years

As of the end of November, Volkswagen had sold 70,000 more cars than General Motors in China in 2013, making it appear inevitable that VW will outsell GM there. The feat would return the German brand to the top of chart in China for the first time in nine years, but even the second-place getter won't be complaining too loudly: both automakers sold more than three million vehicles in a market pegged to hit 16 million sales this year.
Volkswagen said it could have sold more cars if it had had more production capacity in China. The arrival of a new-to-China Audi A4, a China-built A3 sedan, the VW Bora and Skoda Octavia, as well as an $18.2-billion-euro investment in the country to construct new factories, means VW should see its numbers grow in 2014. GM's lineup is expanding next year, too, adding four Chevrolet nameplates and two vehicles to its Baojun brand as it tries to get to five million in sales by 2015.
Among other automakers, Ford benefited from good product and woes for Japanese automakers over a territorial dispute with China, outselling Toyota by almost 32,000 units through the end of November. The Ford Focus is China's best-selling vehicle so far this year.

Ford finds flex-fuel engine design plays big role in emissions output

How bad is ethanol for your engine? There's been a lot of debate on this issue as the US considers upping the biofuel content in the national gasoline supply from 10 percent (E10) to 15 percent (E15). The ethanol industry and some scientists say higher ethanol blends show no "meaningful differences" in new engines while the oil industry says ethanol creates health risks. Researchers working at the Ford Research and Innovation Center decided to take a closer look at how a wide range of gas-ethanol blends - E0, E10, E20, E30, E40, E55 and E80 - affected the emissions coming out of a flex-fuel 2006 Mercury Grand Marquis. To see the full report, printed in the journal Environmental Science & Technology, requires payment, but there is an abstract and Green Car Congress has some more details. The gist is that, "with increasing ethanol content in the fuel, the tailpipe emissions of ethanol, acetaldehyde, formaldehyde, methane, and ammonia increased." At least NOx and NMHC emissions decreased. The researchers say that the effects are due to the fuel and "are expected for all FFVs," but that the way that a manufacturer calibrates the engine will affect NOx, THC, and NMOG emissions. It's this last bit that's important, since the researchers found, "Higher ethanol content in gasoline affects several fundamental fuel properties that can impact emissions. ... These changes can have positive or negative effects that can depend on engine design, hardware, and control strategy. In addition to direct emissions impacts, higher ethanol content fuel can also provide more efficient combustion and overall engine operation under part-load conditions and under knock-limited higher-load conditions." So, as we head towards more ethanol in our fuel supply (maybe), manufacturers are going to need to learn how to burn it most efficiently.