1965 Ford F100 Truck on 2040-cars

Auto blog

How Ford made its 2015 Ford Mustang safer for toupee wearers [w/video]

Ford is ready to tell the story of its 2015 Mustang Convertible, the can't-miss bits being the easier, quicker and quieter roof operation, a more robust roof build for a coupe-like cabin noise, more trunk space, better visibility and reduced in-cabin buffeting. The top release system has been completely redesigned with a single, center-mounted latch on the windshield frame instead of the dual latches of before. The driver can now release the roof without having to lean over into the passenger space, after which the top goes down fully automatically with the press of a button. Ford doesn't say how long it takes to stow, but it's apparently done in half as much time as before, so figure around 8 seconds.
The roof uses a five-bow structure, with the fabric outer and full inner headliner sandwiching ten millimeters of insulation. Detailing work on the top has eliminated "unsightly folds" in the corners when the roof is up and made it more compact when down; its Z-fold assembly is 6.7 inches lower than before at its highest point when put down. Ford says the new electric drive internals make less noise when in operation, and the fully-finished droptop look is achieved with snap-in caps that flank the rear seating and stow in the trunk when not in use (the outgoing Mustang's top was higher and the front when folded and always looked like it was catching air and creating drag).
The compact roof and newly independent rear suspension setup in back means liberated trunk space, 11.4 cubic feet ready to swallow golf bags and tourist swag. You can read a lot more about it in the press release below, check it out in the short video of running footage and learn about the aerodynamic improvements made to the entire Mustang lineup that decrease drag and increase fuel economy.

The USPS needs 180,000 new delivery vehicles, automakers gearing up to bid

Winning the New York City Taxi of Tomorrow tender was a huge prize for Nissan, even though the company is still working through the process of claiming its prize. The United States Postal Service has begun the process to take bids for a new delivery vehicle to replace the all-too-familiar Grumman Long Life Vehicle, and that will be a much larger plum for the automaker who wins it, perhaps worth more than six billion dollars. The Grumman LLV is an aluminum body covering a Chevrolet S-10 pickup chassis and General Motors' Iron Duke four-cylinder engine. The USPS bought them from 1987 to 1994, and the 163,000 of them still in service are a monumental drain on postal resources: they get roughly ten miles to the gallon instead of the quoted 16 mpg, drink up more than $530 million in fuel each year, and their constant repair needs like the balky sliding door and leaky windshields have led the service to increase the annual maintenance budget from $100 million to $500 million. A seat belt is about as modern as it gets for safety technology, and the USPS says that assuming things stay the same, it can't afford to run them beyond 2017. Last year it put out two triage requests for proposals seeking 10,000 new chassis and drivetrains for the Grumman and 10,000 new vehicles. The LLV is also too small for the modern mail system in which package delivery is growing and letter delivery is declining. The service says it doesn't have a fixed idea of the ideal "next-generation delivery vehicles," but it listed a number of requirements in its initial request and is open to any proposal. Carriers have some suggestions, though, saying they want better cupholders, sun visors that they can stuff letters behind, a driver's compartment free of slits that can swallow mail, and a backup camera. The request for information sent to automakers pegs the tender at 180,000 vehicles that would cost between $25,000 and $35,000 apiece, and it will hold a conference on February 18 to answer questions about the contract. GM is the only domestic maker to avow an interest, while Ford and Fiat-Chrysler have remained cagey. Yet with a possible $6.3 billion up for grabs and some new vans for sale that would be advertised on every block in the country, we have a feeling everyone will be listening closely come February 18. We also have a feeling the LeMons series is going to be flooded with Grummans come 2017. News Source: Wall Street Journal, Automotive News - sub.

Ford 3D-printing Mustang out of chocolate and candy for Valentine's Day

Is your beloved in love with the new 2015 Ford Mustang? Do they like chocolate (that's a trick question - everyone likes chocolate)? Are they a bit of a futurist? Then this Hallmark holiday, you need to get them this Ford Mustang, 3D-printed in sweet, delicious chocolate.
Ford is teaming with 3D Systems' Sugar Lab in LA to produce the super-accurate pony car confections in both chocolate and sugar candy varieties. The process kicked off with a CAD rendering of the 2015 Mustang, which was then programmed into the 3D printer. After a bit of work from the machine, a four-inch long, two-inch tall Mustang was the result. Why the tieup with 3D Systems, though?
"We wanted to create something fun to show that while 3D printing made these edible Mustangs, manufacturing-level 3D printing was used in the development of Ford's all-new sports car," said Paul Susalla, Ford's supervisor of 3D printing.