2014 Ford Explorer Limited on 2040-cars

Auto blog

BMW V8-powered Ford Model A is the definition of Hot Rod

Today, hotrodding has a pretty staid definition. Take one classic American car, add one classic American V8, sprinkle with tire smoke and you pretty much have every hot rod to roll out of a shop in the last 40 years. Mike Borroughs knows it wasn't always this way. Once upon a time, getting your bucket to go faster meant grabbing whatever parts were lazing about the yard, bolting them together with a bit of ingenuity and laughing your way down the quarter mile. It's in that spirit that Burroughs built his 1928 Ford Model A.
Rather than turn to the tired flathead or the common Chevrolet small block, Burroughs plucked a 4.0-liter V8 from a 1995 BMW 7 Series. With 300 horsepower and 300 pound-feet of torque, the engine has no trouble shuffling the old A around town. He had to build a custom chassis to get everything to cooperate, but the result is a 1,500-pound heathen that looks built to harass dry lake beds. You can check it out in the video below. Be warned, the soundtrack by Hanni el Khatib may not be safe for work - awesomeness of this caliber rarely is.

Watch these videos of an NHRA racer's bodywork blowing off into a crowd

Just a few months ago, fan safety at racetracks was a hot topic following the last-lap NASCAR Nationwide Series crash at Daytona that sent large pieces of racecars into the grandstands injuring 33 fans. Now, a freak incident at a National Hot Rod Association event resulted in a drag racer's bodywork flying into the crowd at the NHRA Four-Wide Nationals in Charlotte over the weekend. The carbon-fiber body of Robert Hight's Ford Mustang funny car blew off toward the end of a run when his engine exploded, but fortunately, the two fans evaluated after the incident were later released without serious injury.
As you can see in the image above, the body flew high into the air before landing on a walkway in front of the grandstands, a bit of happenstance that likely gave most fans enough time and space to move out of the way. Scroll down to watch a couple of videos showing what happened, including one from a fan's perspective that also reveals what appears to be part of the body's metal bracing landing dangerously close to the crowd.

Ford confirms 1.5-liter EcoBoost four-cylinder engine for 2014 Fusion

Earlier this week, reports were swirling 'round the internet about the 2014 Ford Fusion getting a new 1.5-liter three-cylinder EcoBoost engine. That was... half correct. Ford today confirmed that the 2014 Fusion is, in fact, getting a new 1.5-liter EcoBoost mill, but it has four cylinders, not three.
The new 1.5-liter engine will be the fifth EcoBoost powerplant from Ford Motor Company. Initially to be built at the automaker's Craiova, Romania plant, it will also be offered in the Fusion's twin, the Mondeo, in other markets. This engine will debut at the Shanghai Motor Show next month, and the 1.5-liter is of particular importance in the Chinese market - there is significant tax relief in the People's Republic for vehicles powered by engines with a capacity of 1.5 liters or less.
At a media briefing Thursday, Ford declined to divulge exact power or fuel economy numbers, though Joe Bakaj, vice president of powertrain engineering, told Autoblog that power output should be similar to that of the current 1.6-liter inline-four, and that overall efficiency will be "better than the 1.6." Our earlier report stated that the 1.5-liter four will produce 177 horsepower and 177 pound-feet of torque - losses of 1 hp and 7 lb-ft versus the 1.6-liter engine. Ford states that the 1.5-liter four will feature many of the same technologies used on the company's 1.0-liter EcoBoost inline-three, including an integrated exhaust manifold that recaptures much of the engine's heat.