Explorer Hi- Top 5.4l Rear Wheel Drive Leather Buckets Heated Seats E150 Limited on 2040-cars

Auto blog

Again? Ford issues second 2015 Fusion and Lincoln MKZ seat belt recall

In 2016, Ford issued a recall for 603,392 2013-2016 Fusions and 2013-2015 Lincoln MKZs due to potentially faulty seat belts. Apparently, that wasn't the end of it. Ford announced another recall this week for the same issue, this time covering 108,399 2015 Fusions and MKZs.  In both cases, the seat belt anchor pretensioners are the issue. According to Ford, "increased temperatures generated during deployment of the driver or front-passenger seat belt anchor pretensioner could degrade the tensile strength of the cable below the level needed to restrain an occupant." Basically, heat could weaken the seat belts, and in extreme cases, they wouldn't be able to keep up proper safety standards. Ford knows of at least one injury that has occurred due to this issue.   The recall includes 103,374 vehicles in the United States, 4,002 in Canada, and 1,023 in Mexico. Possibly affected Fusions were built at Ford's Flat Rock Assembly Plant between August 1, 2014 and January 30, 2015. The MKZs were built at the Hermosillo Assembly Plant between August 1, 2014 and November 21, 2014.  As a fix, Ford says dealers will add an extra coating to the seat belt pretensioner cable for protection from the heat. If this recall might affect your vehicle, call your local Ford dealership and use recall reference No. 19S25. This news comes after Ford recalled 1.3 million Fusions and MKZs in 2018 due to the possibility that the steering wheels could fall off. Fusions have also been recalled due to the risk of rolling away.

Focus STs for SEMA include Lotus and Gulf liveries, rally-fied police car

Ford, as we mentioned on Saturday, is pulling out all the stops for November's SEMA show, bringing 57 vehicles to the Las Vegas event. Ford will be staggering the release of its SEMA flotilla, though, so expect to hear a lot about the new additions to the fleet in the weeks to come. We already showed you the Fiesta, Fiesta ST and Mustang models that made up the first batch of SEMA cars. Next up, we have a quartet of modded Focus STs joining Ford's SEMA roster.
Our first Focus ST (pictured above) sports the legendary livery of Gulf Racing. The orange-on-blue scheme, which Ford helped make famous at the 24 Hours of Le Mans, has been updated for 2013, with a more vibrant blue. This ST was built by Universal Technical Institute, while the exterior was done by Neil Tjin of Tjin Edition. Side exhausts, a Vortech supercharger and a Motiv Concepts high-flow cat allow the ST to breathe a bit easier, while Forgestar wheels contrast well with the iconic paint scheme.
Focus ST number two has been done-up by PM Lifestyle and is inspired by "Southern California car culture." Sporting a sleek, pale blue paint job, there's also no shortage of carbon fiber on the car's exterior. The 2.0-liter, turbocharged, four-cylinder engine has been massaged by the likes of Banks Power, COBB Tuning and Ford Racing, while the suspension is wearing a shiny, new set of coilovers and sway bars. The meaty brakes, tucked behind 19-inch, Rotiform wheels, come from Wilwood, while the cabin has been fitted with a pair of Sparco Chrono seats and five-point, Schroth harnesses.

Rising aluminum costs cut into Ford's profit

When Ford reports fourth-quarter results on Wednesday afternoon, it is expected to fret that rising metals costs have cut into profits, even as rivals say they have the problem under control. Aluminum prices have risen 20 percent in the last year and nearly 11 percent since Dec. 11. Steel prices have risen just over 9 percent in the last year. Ford uses more aluminum in its vehicles than its rivals. Aluminum is lighter but far more expensive than steel, closing at $2,229 per tonne on Tuesday. U.S. steel futures closed at $677 per ton (0.91 metric tonnes). Republican U.S. President Donald Trump's administration is weighing whether to impose tariffs on imported steel and aluminum, which could push prices even higher. Ford gave a disappointing earnings estimate for 2017 and 2018 last week, saying the higher costs for steel, aluminum and other metals, as well as currency volatility, could cost the company $1.6 billion in 2018. Ford shares took a dive after the announcement. Ford Chief Financial Officer Bob Shanks told analysts at a conference in Detroit last week that while the company benefited from low commodity prices in 2016, rising steel prices were now the main cause of higher costs, followed by aluminum. Shanks said the automaker at times relies on foreign currencies as a "natural hedge" for some commodities but those are now going in the opposite direction, so they are not working. A Ford spokesman added that the automaker also uses a mix of contracts, hedges and indexed buying. Industry analysts point to the spike in aluminum versus steel prices as a plausible reason for Ford's problems, especially since it uses far more of the expensive metal than other major automakers. "When you look at Ford in the context of the other automakers, aluminum drives a lot of their volume and I think that is the cause" of their rising costs, said Jeff Schuster, senior vice president of forecasting at auto consultancy LMC Automotive. Other major automakers say rising commodity costs are not much of a problem. At last week's Detroit auto show, Fiat Chrysler Automobiles NV's Chief Executive Officer Sergio Marchionne reiterated its earnings guidance for 2018 and held forth on a number of topics, but did not mention metals prices. General Motors Co gave a well-received profit outlook last week and did not mention the subject. "We view changes in raw material costs as something that is manageable," a GM spokesman said in an email.