2007 Ford Crown Victoria Police Interceptor Canine K9 Unit Sedan 4-door 4.6l on 2040-cars

Auto blog

Ford recalling 450,000 Fusion, Mercury Milan sedans

Ford has announced a pair of recalls, and both are critical safety issues. The exponentially larger of the two recall campaigns affects over 450,000 Ford Fusion and Mercury Milan sedans manufactured at the Hermosillo plant between July 21, 2008, and March 4, 2011. The canister purge valve in the fuel tank could malfunction and could cause the top of the tank to crack and leak fuel. That could cause a fire, although Ford "is not aware of any accidents, injuries or fires" resulting from the issue. Affected vehicles will have their ECU software updated and their fuel tanks inspected for potential replacement. The company estimates there are 411,205 affected units in the United States (and its federalized territories), plus another 33,605 in Canada, and 7,055 in Mexico. The second recall affects 13 F-650 trucks. The column shifter's park position mechanism may fracture and let the truck roll away unexpectedly. Those 2016 models built in Ohio between July 29 and September 3, 2015 are all located in the US. Fixing the problem will require replacing the steering column and reconfiguring the instrument panel. FORD ISSUES TWO SAFETY RECALLS IN NORTH AMERICA DEARBORN, Mich., Nov. 23, 2015 – Ford Motor Company is issuing two safety recalls in North America. Ford is not aware of any accidents, injuries or fires related to these conditions. Details are as follows: Ford issues safety recall for certain 2010-2011 Ford Fusion and Mercury Milan vehicles in North America for potential fuel tank issue Ford Motor Company is issuing a safety recall for approximately 450,000 2010-2011 Ford Fusion and Mercury Milan vehicles for a potential issue with the fuel tank. Some of these vehicles might have a canister purge valve that does not work properly, causing internal pressure changes inside the fuel tank. Repeated pressure changes inside the tank could result in a crack on the top of the tank, possibly allowing fuel to leak. A fuel leak in the presence of an ignition source can lead to a fire. Ford is not aware of any accidents, injuries or fires related to this condition. Affected vehicles include certain 2010-2011 Ford Fusion and Mercury Milan vehicles built at Hermosillo Assembly Plant from July 21, 2008 through March 4, 2011. There are a total of approximately 451,865 vehicles that might be affected in North America, including 411,205 vehicles in the United States and federalized territories, 33,605 in Canada and 7,055 in Mexico.

NHTSA closes Ford F-Series Super Duty steering probe without recall

The National Highway Traffic Safety Administration's investigation into 2008 Ford F-250 and F-350 Super Duty pickups, which was originally opened last year, has now ended without a recall. NHTSA was looking into steering failures on some 336,000 trucks.
The issue rested with the steering gear - NHTSA received five complaints of failures - which was redesigned in 2005. According to the report on the matter, investigators "found evidence of broken sector shaft gear teeth and piston damage consistent with incidents of single event overload."
NHTSA investigators, however, "found no evidence of fatigue or material property defects in any of the fractures. Analysis of complaint rates by vehicle build month showed no patterns indicating potential manufacturing quality issues and no difference before and after Ford introduced design changes to the input shaft and sector shaft seals in July 2007 to address potential leak concerns," according to the report, obtained by The Detroit News.

Aluminum lightweighting does, in fact, save fuel

When the best-selling US truck sheds the equivalent weight of three football fullbacks by shifting to aluminum, folks start paying attention. Oak Ridge National Laboratory took a closer look at whether the reduced fuel consumption from a lighter aluminum body makes up for the fact that producing aluminum is far more energy intensive than steel. And the results of the study are pretty encouraging. In a nutshell, the energy needed to produce a vehicle's raw materials accounts for about 10 percent of a typical vehicle's carbon footprint during its total lifecycle, and that number is up from six percent because of advancements in fuel economy (fuel use is down to about 68 percent of total emissions from about 75 percent). Still, even with that higher material-extraction share, the fuel-efficiency gains from aluminum compared to steel will offset the additional vehicle-extraction energy in just 12,000 miles of driving, according to the study. That means that, from an environmental standpoint, aluminum vehicles are playing with the house's money after just one year on the road. Aluminum-sheet construction got topical real quickly earlier this year when Ford said the 2015 F-150 pickup truck would go to a 93-percent aluminum body construction. In addition to aluminum being less corrosive than steel, that change caused the F-150 to shed 700 pounds from its curb weight. And it looks like the Explorer and Expedition SUVs may go on an aluminum diet next. Take a look at SAE International's synopsis of the Oak Ridge Lab's study below. Life Cycle Energy and Environmental Assessment of Aluminum-Intensive Vehicle Design Advanced lightweight materials are increasingly being incorporated into new vehicle designs by automakers to enhance performance and assist in complying with increasing requirements of corporate average fuel economy standards. To assess the primary energy and carbon dioxide equivalent (CO2e) implications of vehicle designs utilizing these materials, this study examines the potential life cycle impacts of two lightweight material alternative vehicle designs, i.e., steel and aluminum of a typical passenger vehicle operated today in North America. LCA for three common alternative lightweight vehicle designs are evaluated: current production ("Baseline"), an advanced high strength steel and aluminum design ("LWSV"), and an aluminum-intensive design (AIV).