2013 Ford C-max Hybrid Sel on 2040-cars

Auto blog

Ford F-150 EcoBoost in NHTSA probe for acceleration issue

According to Automotive News, the National Highway Traffic Safety Administration is launching a probe into 400,000 Ford F-150 models over possible acceleration problems. According to the article, NHTSA has received 95 reports "alleging incidents of reduced engine power during hard accelerations" on 2011 to 2013 F-150 models equipped with the company's 3.5-liter EcoBoost V6 engine.
Automotive News reports that Ford has issued three technical service bulletins "related to intermittent stumble/misfire on acceleration from highway cruise in humid or damp conditions," according to the government agency's documents. About one third of the 95 reports NHTSA has received cited humid or rainy conditions when these problems allegedly occurred.
These technical service bulletins have allowed dealers to address a "condition related to moisture accumulation in the charge air cooler during extended highway cruising at constant throttle in humid or damp conditions," AN reports, citing NHTSA documents. Furthermore, the TSB outlines details for "reprogramming the powertrain control module with the latest calibration and installing a new CAC and air deflector plate."

Tier 1 suppliers call GM the worst OEM to work with

Among automakers with a big US presence, General Motors is the worst to work for, according to a new survey from Tier 1 automotive suppliers, conducted by Planning Perspectives, Inc.
The Detroit-based manufacturer, which has been under fire following the ignition switch recall and its accompanying scandal, finished behind six other automakers with big US manufacturing operations. Suppliers had issues with trust and communications, as well as intellectual property protection. GM was also the least likely to allow suppliers to raise their prices in the face of unexpected increases in material cost, all of which contributed to 55 percent of suppliers saying their relationship with GM was "poor to very poor."
GM's cross-town competitors didn't fare much better. Chrysler finished in fifth place, ahead of GM and behind Dearborn-based Ford, which was passed for third place this year by Nissan. Toyota took the top marks, while Honda captured second place.

Rising aluminum costs cut into Ford's profit

When Ford reports fourth-quarter results on Wednesday afternoon, it is expected to fret that rising metals costs have cut into profits, even as rivals say they have the problem under control. Aluminum prices have risen 20 percent in the last year and nearly 11 percent since Dec. 11. Steel prices have risen just over 9 percent in the last year. Ford uses more aluminum in its vehicles than its rivals. Aluminum is lighter but far more expensive than steel, closing at $2,229 per tonne on Tuesday. U.S. steel futures closed at $677 per ton (0.91 metric tonnes). Republican U.S. President Donald Trump's administration is weighing whether to impose tariffs on imported steel and aluminum, which could push prices even higher. Ford gave a disappointing earnings estimate for 2017 and 2018 last week, saying the higher costs for steel, aluminum and other metals, as well as currency volatility, could cost the company $1.6 billion in 2018. Ford shares took a dive after the announcement. Ford Chief Financial Officer Bob Shanks told analysts at a conference in Detroit last week that while the company benefited from low commodity prices in 2016, rising steel prices were now the main cause of higher costs, followed by aluminum. Shanks said the automaker at times relies on foreign currencies as a "natural hedge" for some commodities but those are now going in the opposite direction, so they are not working. A Ford spokesman added that the automaker also uses a mix of contracts, hedges and indexed buying. Industry analysts point to the spike in aluminum versus steel prices as a plausible reason for Ford's problems, especially since it uses far more of the expensive metal than other major automakers. "When you look at Ford in the context of the other automakers, aluminum drives a lot of their volume and I think that is the cause" of their rising costs, said Jeff Schuster, senior vice president of forecasting at auto consultancy LMC Automotive. Other major automakers say rising commodity costs are not much of a problem. At last week's Detroit auto show, Fiat Chrysler Automobiles NV's Chief Executive Officer Sergio Marchionne reiterated its earnings guidance for 2018 and held forth on a number of topics, but did not mention metals prices. General Motors Co gave a well-received profit outlook last week and did not mention the subject. "We view changes in raw material costs as something that is manageable," a GM spokesman said in an email.