Nav Cd 107-kw Electric Motor (std) Front Wheel Drive Power Steering Abs on 2040-cars

Auto blog

Autocar pits Formula Ford against Germany's finest

Ford has quite the racing pedigree, but usually, its racers are relegated to the track. Not the new Formula Ford EcoBoost, though. It's a turbocharged, open-wheeled racer complete with a 200-horsepower, 1.0-liter, three-cylinder engine... and it's legal on the roads of the UK.
That's stressed in this video from Autocar, with the mag going so far as to show the car's tax disc and license plates. Being a road-legal offering, it's tempting to see just how well an open-wheeler that delivers racecar-like performance while also netting over 100 miles per gallon (assume this is on the British cycle, for obvious reasons) stacks up against modern performance cars.
Autocar lined up the Formula Ford against an Audi R8 V10, a BMW M6 Gran Coupe and a Mercedes-Benz A45 AMG in a number of situations to see which would come out on top. Take a look below for the full video.

Ford recalling 2015 Mustang for fuel line leak, 20K Transit Connects for plastic panel

Ford is recalling 738 examples of the 2015 2015 Mustang with the 2.3-liter EcoBoost engine – 712 in the US, 16 in Canada. A fuel pressure sensor might have been installed incorrectly on the affected cars, and that could result in a fuel leak. At the time of writing the company hasn't heard any reports of any incidents related to the issue, and parties with affected vehicles can take them to the dealer to have the fuel tube assembly replaced free of charge. The 2014 Transit Connect Cargo Van is also the subject of a safety recall, due to a possible problem with adhesive used on the exterior plastic panel on the sliding doors. There are 19,825 units covered by that recall, which dealers will also repair free of charge. You can find more information on both bulletins in the press releases below. Ford Issues Safety Recall for Certain 2015 Mustang Vehicles in North America for Fuel Pressure Sensor Issue Dec 4, 2014 | DEARBORN, Mich. - Ford is issuing a safety recall for approximately 730 2015 Ford Mustang vehicles in North America (actual 728) for a potential fuel line leak. A fuel pressure sensor, which is part of the fuel supply tube assembly, may have been installed incorrectly, potentially resulting in a pressurized fuel leak. A fuel leak in the presence of an ignition source may result in a fire. Ford is not aware of any fires, accidents or injuries related to this condition. Affected vehicles include certain 2015 Ford Mustangs equipped with 2.3-liter engines built at Flat Rock Assembly Plant, Sept. 25, 2014 to Oct. 9, 2014. Ford is aware of 712 vehicles in the United States and federalized territories and 16 in Canada. These totals are as of Dec. 3, 2014. Dealers will replace the fuel supply tube assembly at no cost to the customer. *** Ford Issues Safety Recall for Certain 2014 Transit Connect Cargo Van Vehicles in North America for Issue with the Plastic Panel on the Sliding Doors Dec 4, 2014 | DEARBORN, Mich. - Ford is issuing a safety recall for approximately 20,000 2014 Transit Connect cargo van vehicles in North America (actual 19,825) for an issue with adhesion of an exterior plastic panel to the sliding doors. This issue may result in noise, a water leak, a loose panel, or separation of the plastic panel from the vehicle while driving, potentially increasing the risk of an accident or injury. Ford is not aware of any accidents or injuries related to this condition.

Ford 3D-printing Mustang out of chocolate and candy for Valentine's Day

Is your beloved in love with the new 2015 Ford Mustang? Do they like chocolate (that's a trick question - everyone likes chocolate)? Are they a bit of a futurist? Then this Hallmark holiday, you need to get them this Ford Mustang, 3D-printed in sweet, delicious chocolate.
Ford is teaming with 3D Systems' Sugar Lab in LA to produce the super-accurate pony car confections in both chocolate and sugar candy varieties. The process kicked off with a CAD rendering of the 2015 Mustang, which was then programmed into the 3D printer. After a bit of work from the machine, a four-inch long, two-inch tall Mustang was the result. Why the tieup with 3D Systems, though?
"We wanted to create something fun to show that while 3D printing made these edible Mustangs, manufacturing-level 3D printing was used in the development of Ford's all-new sports car," said Paul Susalla, Ford's supervisor of 3D printing.