2003 Dodge Stratus R/t Coupe 2-door 3.0l on 2040-cars

Auto blog

2013-14 Dodge Viper recalled over faulty door handles

The 2013-14 Dodge Viper is getting a voluntary recall affecting 1,762 cars worldwide to replace their door-handle assemblies. Of the affected vehicles, FCA US reports there are 1,451 in the US, 160 in Canada, 17 in Mexico and 59 of them outside of NAFTA. After receiving three reports of doors either not closing or opening while driving a low speeds, FCA US engineers found a new sealant from a supplier didn't provide sufficient moisture protection to the electronic switches for the door latches. If the parts get wet, this can potentially cause a short circuit. The automaker is quite clear that are no reports of accidents of injuries from this problem. As always, the recall repairs will be done at no cost to owners, and FCA US will be getting in touch with customers soon about the problem. Related Video: Statement: Door-handle Assemblies April 9, 2015 , Auburn Hills, Mich. - FCA US LLC is voluntarily recalling an estimated 1,762 cars globally to replace their door-handle assemblies. FCA US launched an investigation after the Company received three warranty claims linked to doors that failed to close or opened inadvertently while vehicles were moving at low speed. The Company is unaware of any related injuries or accidents. Engineers determined a sealant, newly adopted by a supplier, provided inconsistent moisture protection to the electronic switches that control the door latches. Switches exposed to moisture may short-circuit. Affected are approximately 1,451 model-year 2013-14 Dodge Viper SRT cars in the U.S.; 160 in Canada; 17 in Mexico and 59 outside the NAFTA region. Affected customers will be notified and advised when they may schedule service, which will be performed at no cost. Customers with questions may call the FCA US Customer Information Center at 1-800-853-1403.

Dodge Demon makes so much torque, it needs stronger driveline parts

Torque is a lovely thing, a sweet and wonderful force that twists and pulls and can help propel a two-ton metal box forward at comical speeds. Torque is also fickle and will bend and break those same metal parts without a second thought, which is why the new Dodge Demon is compensating for its increased torque with some new re-engineered and reinforced parts. And there's software intended to combat wheel hop, which one of the most dramatic ways torque can break stuff. Week 8's video, "Race-hardened Parts," gives a hint towards what all these new parts can do. While we still don't know how much torque the Demon will throw out, we do know it's enough to warrant an upgraded prop shaft, half shafts, and a differential housing. The Challenger Hellcat, which is the basis for the Demon, makes 650 pound-feet of torque already. The new parts will go a long way toward making sure the work from the Demon's engine is properly translated into motion by those Nitto drag radials. The new prop shaft uses high-strength steel, heat-treated stub-shafts, and increases the tube thickness by 20 percent for a 15 percent increase in torque capacity. Additionally, Dodge says the upgraded differential housing allows for a 30 percent increase in torque capacity by using heat-treated A383 aluminum alloy and a higher strength shot-peened gear set. The 41-spline half shafts that deliver 20 percent increased torque capacity through the use of high-strength low alloy steel and 8-ball joints. In addition to the hardware, the Launch Assist software has been tuned to help alleviate wheel hop. Dodge says the Demon is the first factory production car that uses wheel speed sensors to detect hop and momentarily cut torque to compensate. This means a driver can keep their foot planted on the floor while the computer sorts out the traction. Previously, the best solution was to back off the throttle to manually cut the load. Finally, the Dodge Demon will offer a four-point harness mounting bar as an optional accessory. The part will be supplied by Speedlogix and fits in place of the deleted rear seat. Customers can install the bar without having to hack apart their cars to find a proper mounting point. Look for more teasers and info on ifyouknowyouknow.com in the lead-up to the Demon's debut at the 2017 New York Auto Show. Related Video: Image Credit: FCA Dodge Performance dodge demon dodge hellcat

Chrysler teases upcoming outlay of SEMA cars

Fiat Chrysler Automobiles is hauling a multitude of modified models to the annual SEMA show in Las Vegas this November, and the company is releasing the first teasing sketches of many of them.
Unfortunately, FCA isn't giving many solid details on any of the concepts other than saying the vehicles from Chrysler, Jeep, Dodge, Ram and Fiat all benefit from tuning from its Mopar performance brand. The teaser photos include a sinister-looking Chrysler 200S, Fiat 500 Abarth with two-tone paint and a scorpion on the hood, a red and black 500L, seemingly two different takes on the Jeep Renegade, a green Dodge Challenger wearing the T/A badge, an orange and black Dart, a very neon Charger, just the outline of a red and black Viper, a Ram ProMaster in Mopar livery and a Ram pickup called the Outdoorsman.
Take a look through the gallery to see what you think of the sketches for these concepts, and scroll down for the full announcement from FCA.