1993 Dodge Stealth R/t Turbo Hatchback 2-door 3.0l on 2040-cars

Auto blog

2019 Dodge Challenger R/T Scat Pack Widebody Drivers' Notes | Widebody for everybody

The 2019 and soon to be 2020 Dodge Challenger R/T Scat Pack Widebody is another Challenger dart thrown against the wall by Dodge. It takes the desirable Widebody package we’ve seen on Hellcats and applies it to the naturally aspirated Scat Pack with the 6.4-liter V8. This kit includes stiffer adaptive shocks, stiffer springs, larger stabilizer bars, big Brembo brakes, a 3.09 rear axle ratio, 20-inch forged wheels and massive 305 section-width tires on all four corners. Most important of all, you get the special Widebody fender flares that give the car its signature look. The package is $6,000 on top of a regular Scat Pack. That means the cheapest youÂ’ll step into a Scat Pack Widebody is $46,740. The Widebody that rolled through our offices came in at a much-higher $57,295 after a number of options were tacked on. Many of these, you can skip. The 485 horsepower and 475 pound-feet of torque that comes standard is the most important aspect of this big coupe. Several packages costing more than $1,000 each add convenience and driver assistance tech, and the Harman/Kardon system is a hefty $1,595. With such a loud engine and exhaust, itÂ’s hardly worthwhile. Our tester also had the $1,595 eight-speed automatic transmission. ThisÂ’ll let you scare unsuspecting bystanders with the remote start system, but opting for a manual is an easy way to save some cash and increase driver involvement. With all the modern technology like adaptive cruise control, auto high-beams, heated and cooled seats, and blind-spot detection, the Challenger tries its best to keep up with the times. ItÂ’s no technological marvel, but itÂ’s neat to see some of these options available for folks who might want them. Still, tech gizmos are not what the Widebody is about. This Challenger keeps the same personality as all of those before it, but adds a dash of handling and hostility to its outward appearance. Here are our varied experiences with it during a week of testing. Editor-in-Chief, Greg Migliore: Yes, you can put a rear-facing convertible car seat in a Dodge Challenger. I did. It actually wasnÂ’t that hard. Remember, the Challenger is genetically a Mercedes sedan and shares underpinnings with the Dodge Charger. The biggest hurdles are ingress and egress, which is to be expected in any coupe. The roofline is low, but really not that bad. I simply lifted my toddler and maneuvered him into the backseat.  I was able to get him secured and fastened, and then I just stepped out of the car.

Mopar unveils Dodge Challenger Drag Pak [w/video]

Dodge is going drag racing, and it's doing it with an all-new version of the Challenger for NHRA's Sportsman class. FCA's Mopar parts and performance arm announced the new Challenger Drag Pak Friday, showing off a version with a 354-cubic-inch (that's a 5.8-liter, by the way), supercharged V8 and a 426-ci (7.0-liter), naturally aspirated V8 – both Hemis, of course – that can get the big coupes through the quarter-mile in "the eight-second range." While the two engines deliver similar performance, at their base, they're quite a bit different. The supercharged model uses a cast-iron block, while the 426 has aluminum for both the block and head. That said, both models get customized engine calibrations, and are mated to unique, race-spec automatic transmissions. But drag racing is about far more than just outright power. Mopar significantly updated the four-link rear suspension, adding a four-inch rear axle from Strange Engineering, along with an aluminum, nine-inch third member, while the rear-axle housing has been strengthened in general. Both the rear shocks and front struts can be adjusted for rebound and compression, too. Lightweight 15-inch wheels, meanwhile, are shod in super-sticky Hoosier drag radials, with nine inches of tread in back and 4.5 inches in front. The new Challenger Drag Pak should run the quarter-mile in "the eight-second range." In the cabin, there's an NHRA-spec roll cage, a Racepak gauge cluster, and a handsome pair of Sparco racing seats. Outside, supercharged models get blue decals, while naturally aspirated varieties get black stickers, although there's more to the new Challenger dragster's exterior than just its decals. Mopar tweaked the big-scoop hood, promising it's easier to get up to check on the engine, and the designers also added trailer tie-down straps in both the front and rear. While the dragster was the big news today, Mopar officials also announced the two enhanced Scat Pack kits for both the Dodge Charger and Challenger R/T. The 5.7-liter Hemi models gain an extra 56 horsepower and 30 pound-feet of torque in the Scat Pack 2 thanks to a new cam, valve springs, pushrods, and gaskets. The Scat Pack 3, meanwhile, adds 75 hp and 44 lb-ft, on top of the gains from the lower packages. That should be perfect for drivers who wish to snort in the face of their SRT 392-driving friends. The third stage adds a ported cylinder heads, as well as high-flow manifolds and catalysts.

Chrysler to accelerate production of 2013 Ram and V6 engines

Chrysler is adding a third shift at its Warren Truck plant to meet demand for the new 2013 Ram pickup. And with tight supplies of its Pentastar V6, the company is also boosting output at its Mack Engine plant.
The expansions will add 1,250 jobs and are part of a $238 million investment by Chrysler in the Detroit area. Warren's third shift will begin work sometime in the spring, a Chrysler rep told Automotive News. Mack's increased Pentastar production a could include both 3.6 and 3.2-liter engines.
The company says it also plans to invest $40 million in its Trenton Engine plant to allow for production of a 3.2-liter V6 as well as the Tigershark inline-four for the upcoming Jeep Liberty replacement.