Dodge Ram 3500 4x4 Diesel Cummins on 2040-cars

Auto blog

Chrysler recalling 2009-2010 Ram 1500, Dodge Dakota pickups over axle pinion nut

Chrysler is issuing a recall for the 2009 and 2010 Ram 1500 and Dodge Dakota pickup trucks due to improper installation of the rear axle pinion nut. According to the National Highway Traffic Safety Administration, a total of 44,300 trucks are affected by the recall, and there have been 12 confirmed incidents including one crash.
The issue on both trucks is that the pinion nut is loosening on some trucks due to a lack of thread adhesive, and it is causing the rear axle to lock up resulting in loss of vehicle control. NHTSA's recall notice says that eight incidents occurred at speeds over 35 miles per hour and most also exhibited driveshaft failures as well since the loss of the pinion nut would cause the gear to separate from the driveshaft. In one complaint, the driveshaft separated from the rear axle and punctured the gas tank.
Chrysler will begin sending out recall notices to affected owners in November, but scroll down to see the official NHTSA notice.

FCA recalls 570,000 SUVs from Jeep and Dodge over fire woes

Fiat Chrysler US has issued two recalls covering a total of about 570,000 Jeep and Dodge models. The first concerns vanity mirror wiring in the Jeep Grand Cherokee from the 2011 and 2012 model years, and in Dodge Durango units built before September 12, 2012. The automaker recalled almost 900,000 units last year to repair the issue, then faced more issues this year when the fires continued in repaired vehicles. This new recall seeks to resolve the issue, FCA saying that the post-recall fires happened in a tiny percentage of vehicles equipped with a specific wiring package. This recall is for 352,831 total units in the US, another 26,478 in Canada, 13,037 in Mexico, and 84,330 internationally. No injuries or deaths have been reported. FCA says it will inform customers as to when they can schedule a service visit to remedy the issue. The second recall takes aim at 60,107 examples of the Jeep Compass and Patriot from the 2015 model year in the US, plus 5,755 in Canada, 3,351 in Mexico, and 23,995 in other markets. Those models could suffer from an out-of-position clamp on the power steering fluid line. The error could allow fluid to leak, increasing the risk of a fire if the fluid ends up on a hot surface. In the case of a complete loss of fluid, drivers will need to use a lot more effort to steer. The automaker reports no injuries or accidents, and will advise customers when to head to the dealer for service. Related Video: Jeep Grand Cherokee and Dodge DurangoStatement: Vanity-Mirror WiringDecember 24, 2015 , Auburn Hills, Mich. - FCA US LLC is recalling an estimated 352,831 SUVs in the U.S. to help ensure vanity-mirror wiring may be serviced more consistently.Overheating conditions were reported among a small percentage of vehicles (<0.02%) serviced in connection with a related recall, conducted previously.** An FCA US LLC investigation discovered the service procedure, if not followed precisely, may leave vehicles susceptible to a short-circuit, creating a potential fire hazard.The Company is unaware of any related injuries or accidents. Post-service overheating conditions were observed only in vehicles equipped with a certain wiring package. These vehicles were produced before Sept. 2, 2012.Affected are model-year 2011-2012 Jeep Grand Cherokee and Dodge Durango SUVs produced before Sept. 2, 2012. Wiring in the headliners of these vehicles will be secured with a new adhesive.

Dodge Viper recall requires small-handed mechanics

It has been over a year since Chrysler first announced its recall of 3,660 2003-2004 Dodge Vipers because the airbag could suddenly deploy. The repairs are finally beginning, and it appears to be a nightmare for mechanics.
According to the automaker's filing with the National Highway Traffic Safety Administration, the airbag control module can fail, which causes the bag or the seatbelt pre-tensioner to deploy without warning. It took over a year to design the new parts, according to The New York Times. However, Chrysler finally has a new "jumper harness with an in-line diode filter circuit" ready to fix the problem.
The dilemma now moves to the mechanics who have to actually install the part. A 47-step guide from Chrysler explains that the procedure should take about two hours. It's not an easy job, though. Most of the dashboard has to be taken apart, and the instructions include this helpful bit of advice: "Installing the jumper harness and filter box into position is not an easy task. Patience, perseverance, and small hands are required." We wish the best of luck to them. The fix comes just in time for the Vipers to enjoy the summer sun.