2002 Dodge Ram 3500 on 2040-cars

Auto blog

Dodge Hornet supposedly snapped inside Alfa Romeo Tonale factory

It appears that someone in Stellantis' Pomigliano d’Arco Assembly Plant in Italy couldn't keep their cellphone to themselves. Video uploaded to the Alfa Romeo Club Italia Facebook page, then quickly removed, purports to show Dodge's brand-engineered version of the Alfa Romeo Tonale in the same factory where the Alfa will be built. The Dodge is expected to be called the Hornet, and there are a few differences between it and and Alfa Romeo, which is understandable. But if the screenshots on Twitter are accurate, then the Dodge looks a lot closer to the Alfa Romeo than perhaps anyone expected. The front fascia and hood fall in line with Dodge's design language. The Alfa grille is replaced by a narrow, stepped upper grille, and the hood is one of the vented units similar to those available for Dodge's R/T performance trims. And as Mopar Insiders noticed, the silhouette of this car's front end matches a vehicle silhouette Dodge showed during Stellantis' 2021 EV Day.   Inside, the Italian brand's crest in the steering wheel center cap is replaced by Dodge's twin slashes, and the steering wheel has been stripped of the large, curved paddle shifters the Tonale showed on its debut. There's still a start/stop button on the steering wheel, but where the Tonale has a driving mode dial on its dash, this supposed Hornet has another start/stop button. Dodge's push-to-start buttons are usually on the instrument panel, so our guess is that the wheel is a holdover for testing. On the center tunnel, the parking alert buttons and Italian Tricolore flag on the Alfa Romeo are replaced by three different buttons.   We've known Dodge has two electrified vehicles on the way, and the Hornet name has been low-key buzzing for two years. Fiat Chrysler applied to trademark the name in the U.S. in March 2020; at the time, it was thought a vehicle with that name could replace the Journey. In 2021, a July rumor out of Italy was the first whisper of the Hornet name being attached to the Alfa Romeo Tonale. In August, when Stellantis CEO Carlos Tavares said Dodge would get a PHEV in 2024, watchers pegged that model as the Hornet. That hybrid powertrain would show a year after the vehicle's launch, the Hornet anticipated as a 2023 model with the Tonale's turbocharged 2.0-liter four-cylinder. That engine could get the same 256 horsepower and 295 pound-feet of torque as the Tonale, or be boosted to satisfy Dodge's performance credentials.

Chrysler readying Hellcat V8 with Viper-like power

A monstrous supercharged V8 engine could be in store for Chrysler and SRT products, if recent rumors are to be believed. Allpar is reporting that the forced-induction V8 - Chrysler's first, if this goes down - could make its debut this summer.
The story goes that the Hellcat would be based on a 6.2-liter Hemi engine, rather than on the existing 5.7- or 6.4-liter versions of the company's vaunted mill. In any case, the general consensus is that the motor will have gobs of power. Modest estimates call for between 500 to 570 horsepower, with some outliers predicting a figure as high as 600 hp. That figure would put the output would place the Hellcat awfully close to that of the 640-hp V10 in the SRT Viper, too. Allpar contends that a slightly lower powered version would allow Chrysler to keep costs below that of the more powerful Ford Shelby GT500, which might be a sweet spot.
The Hellcat could debut in a number of SRT products. SRT versions of the Charger, Challenger and 300 are all up for grabs, as is the rumored SRT Barracuda.

Dodge Viper to out-Hell the Hellcat with supercharged V10?

The Viper wouldn't be the Viper if it wasn't the most powerful model under the Chrysler umbrella. But with the arrival of the Hellcat engine in the Dodge Charger and Challenger, the Viper has fallen behind in the bragging rights department: where the new supercharged V8 produces 707 horsepower and 650 pound-feet of torque, the naturally aspirated V10 offers "only" 640 hp and 600 lb-ft - gargantuan output figures by almost any other standard, but crucially behind on the SRT power scale. Conner Avenue is going to have to do something about that.
Although the Hellcat's engine reportedly won't fit under the Viper's hood, SRT is now rumored to have another trick up its sleeve: supercharge the existing V10. According to the Pentastar performance enthusiasts at allpar.com, Chrysler has already taken delivery of the first such prototype engines so that it can begin the process of fitting it into an upgraded Viper.
The spooled ten-pot is tipped to produce around 800 hp and 650 lb-ft of torque. More than that and the Viper's drivetrain, chassis and bodywork would have to be substantially reworked. Though beefier transmissions are available, fitting them would reportedly set off a domino-game of changes required to handle the added torque. Which may be something Chrysler would be prepared to do for the next-generation model, but in the meantime, 800 hp could prove enough to put the Viper back atop the Mopar performance ladder where it belongs, and give it an edge against the new Corvette Z06 to rekindle sales.