2001 Dodge Diesel 5.9 Cummings Parting Out 4wd Manual Dually on 2040-cars

Auto blog

2014 Dodge Journey Crossroad

Watchers of the auto industry will notice a theme among the formerly bankrupted American automakers, General Motors and Chrysler. There are the post-bankruptcy vehicles, and the pre-bankruptcy vehicles. The former, in the case of Chrysler, include the Jeep Grand Cherokee, as well as the 200 and 300. For GM, there's the Cadillac ATS, Chevrolet Impala and Buick Encore, among others. These vehicles have the freshest styling, with sharp exteriors and well-crafted interiors, as well as advanced powertrains and well-sorted chassis.
As for the pre-bankruptcy vehicles, they tend to be easy to spot. Most suffer from inferior driving dynamics, cheaper interiors, poorer fuel economy and often homely looks (we know, there were some decent cars before the bankruptcy, but they were pretty heavily outweighed by the bad ones). Think late, last-generation Chevrolet Impala or Chrysler 200. Increasingly, though, we're seeing vehicles that split the balance between pre- and post-bankruptcy. Vehicles like the Dodge Journey.
The Journey debuted in 2007 as a 2008 model year vehicle, meaning it should fall into the latter category. But heavily breathed upon in 2011, it now enjoys a new, 3.6-liter Pentastar V6, a big, critically acclaimed touchscreen display and in the case of today's tester, a new-for-2014 Crossroad spec.

Mopar unveils Dodge Challenger Drag Pak [w/video]

Dodge is going drag racing, and it's doing it with an all-new version of the Challenger for NHRA's Sportsman class. FCA's Mopar parts and performance arm announced the new Challenger Drag Pak Friday, showing off a version with a 354-cubic-inch (that's a 5.8-liter, by the way), supercharged V8 and a 426-ci (7.0-liter), naturally aspirated V8 – both Hemis, of course – that can get the big coupes through the quarter-mile in "the eight-second range." While the two engines deliver similar performance, at their base, they're quite a bit different. The supercharged model uses a cast-iron block, while the 426 has aluminum for both the block and head. That said, both models get customized engine calibrations, and are mated to unique, race-spec automatic transmissions. But drag racing is about far more than just outright power. Mopar significantly updated the four-link rear suspension, adding a four-inch rear axle from Strange Engineering, along with an aluminum, nine-inch third member, while the rear-axle housing has been strengthened in general. Both the rear shocks and front struts can be adjusted for rebound and compression, too. Lightweight 15-inch wheels, meanwhile, are shod in super-sticky Hoosier drag radials, with nine inches of tread in back and 4.5 inches in front. The new Challenger Drag Pak should run the quarter-mile in "the eight-second range." In the cabin, there's an NHRA-spec roll cage, a Racepak gauge cluster, and a handsome pair of Sparco racing seats. Outside, supercharged models get blue decals, while naturally aspirated varieties get black stickers, although there's more to the new Challenger dragster's exterior than just its decals. Mopar tweaked the big-scoop hood, promising it's easier to get up to check on the engine, and the designers also added trailer tie-down straps in both the front and rear. While the dragster was the big news today, Mopar officials also announced the two enhanced Scat Pack kits for both the Dodge Charger and Challenger R/T. The 5.7-liter Hemi models gain an extra 56 horsepower and 30 pound-feet of torque in the Scat Pack 2 thanks to a new cam, valve springs, pushrods, and gaskets. The Scat Pack 3, meanwhile, adds 75 hp and 44 lb-ft, on top of the gains from the lower packages. That should be perfect for drivers who wish to snort in the face of their SRT 392-driving friends. The third stage adds a ported cylinder heads, as well as high-flow manifolds and catalysts.

Dodge Viper ACR reportedly green lit [w/video]

The Dodge Viper might be getting a little more venomous in the near future thanks to a return of the performance-honed ACR trim. According to an anonymous source leaking the info to Allpar, the version would go into production in July as a 2016 model year vehicle. FCA US showed a concept for a future ACR (pictured above) at the 2014 SEMA Show that sported carbon fiber parts for the front splitter and dive planes, plus a picnic-table-sized rear wing. The body also received ducts at the rear to shoot cool air to the differential. A set of 15.4-inch carbon-ceramic brake rotors also brought things to a halt in a hurry. The company promised all the aero pieces were sculpted in the wind tunnel to give the coupe even more downforce. To shed weight, engineers chucked the radio, speakers, carpet and sound deadening out of the interior, and they replaced many bits with even more carbon fiber. All of the tweaks are necessary because the ACR moniker carries serious cachet for the Viper at the track, especially at the Nurburgring. One reportedly did a 7:22 lap around the 'Ring in 2008, and another improved that further to 7:12 in 2011. Autoblog reached out to FCA US for comment about the possibility for the hotter Viper, but the company wasn't willing to comment about any possible, future projects. Related Video: