2005 Dodge Ram 2500 Slt Quad Cab 5.9l Cummins on 2040-cars

Auto blog

SRT reveals Satin Vapor Edition 300, Charger and Challenger SRT models

With the exception of some notable truck and van introductions, Chrysler brands have tended to use the Chicago Auto Show to bring out new special editions, pimp their aftermarket parts support or indulge in the occasional flight of fancy. That plan is holding true for 2014, as well. Cases in point are these new Satin Vapor Editions of the 2014-model-year Dodge Challenger, Dodge Charger and Chrysler 300 - all from SRT.
The Satin Vapor name may sound like a failed 1970s glam-rock band, or a pseudo-gynecological diagnosis from the Old West, but is, in fact, pretty much a tape-and-trim package for this trio of hi-po Mopars. 300, Challenger and Charger alike come shod with 20-inch aluminum wheels finished in Black Satin Vapor Chrome, and are accented with Satin Black bits aplenty. The 300 gets blacked-out mirrors, spoiler and roof; the Challenger applies it to mirrors and its fuel door; while the Charger has the stuff covering its roof, hood and Super Bee tail graphic.
Interiors of the cars have been mildly updated as well, with all three getting some combination of Nappa leather, ultra-suede and carbon-fiberish finishes.

Dodge Charger to slim down and run turbo four in next generation

The current Dodge Charger is getting long in the tooth. It was originally introduced in 2005 as a 2006 model. In car terms, that's an eternity, though it's been refreshed twice. Still, FCA US will keep the LX-generation car going, reportedly facelifting it one last time for 2019. After that, there are some bigger changes in store . Automotive News is reporting that the follower to the current LX Charger will lose almost 500 pounds and will once again offer a turbo four-cylinder. You might remember the front-wheel-drive four-banger Charger of the early '80s. The recharged sedan will be twin-turbo and it's going to use the 300-horsepower four-cylinder engine currently under development for the 2018 Jeep Wrangler, AN says. The target weight for the future car is around 3,500 lbs, while the current car has a curb weight of nearly 4,000 lbs. Look for it to arrive in the early 2020s. The new platform will have a touch of Italian flair instead of the Daimler-Benz flavor embedded deep inside the LX cars. It will be built on an extended version of the 2017 Alfa Romeo Giulia's "Giorgio" platform, according to AN. Dealers were already shown a styling-buck almost a year ago. Related News: Featured Gallery 2015 Dodge Charger R/T View 42 Photos News Source: Automotive NewsImage Credit: AOL Alfa Romeo Dodge Future Vehicles Sedan FCA

Mopar unveils Dodge Challenger Drag Pak [w/video]

Dodge is going drag racing, and it's doing it with an all-new version of the Challenger for NHRA's Sportsman class. FCA's Mopar parts and performance arm announced the new Challenger Drag Pak Friday, showing off a version with a 354-cubic-inch (that's a 5.8-liter, by the way), supercharged V8 and a 426-ci (7.0-liter), naturally aspirated V8 – both Hemis, of course – that can get the big coupes through the quarter-mile in "the eight-second range." While the two engines deliver similar performance, at their base, they're quite a bit different. The supercharged model uses a cast-iron block, while the 426 has aluminum for both the block and head. That said, both models get customized engine calibrations, and are mated to unique, race-spec automatic transmissions. But drag racing is about far more than just outright power. Mopar significantly updated the four-link rear suspension, adding a four-inch rear axle from Strange Engineering, along with an aluminum, nine-inch third member, while the rear-axle housing has been strengthened in general. Both the rear shocks and front struts can be adjusted for rebound and compression, too. Lightweight 15-inch wheels, meanwhile, are shod in super-sticky Hoosier drag radials, with nine inches of tread in back and 4.5 inches in front. The new Challenger Drag Pak should run the quarter-mile in "the eight-second range." In the cabin, there's an NHRA-spec roll cage, a Racepak gauge cluster, and a handsome pair of Sparco racing seats. Outside, supercharged models get blue decals, while naturally aspirated varieties get black stickers, although there's more to the new Challenger dragster's exterior than just its decals. Mopar tweaked the big-scoop hood, promising it's easier to get up to check on the engine, and the designers also added trailer tie-down straps in both the front and rear. While the dragster was the big news today, Mopar officials also announced the two enhanced Scat Pack kits for both the Dodge Charger and Challenger R/T. The 5.7-liter Hemi models gain an extra 56 horsepower and 30 pound-feet of torque in the Scat Pack 2 thanks to a new cam, valve springs, pushrods, and gaskets. The Scat Pack 3, meanwhile, adds 75 hp and 44 lb-ft, on top of the gains from the lower packages. That should be perfect for drivers who wish to snort in the face of their SRT 392-driving friends. The third stage adds a ported cylinder heads, as well as high-flow manifolds and catalysts.