2003 Dodge Slt on 2040-cars

Auto blog

Big rig gets blown over on Wyoming freeway, flattens police cruiser

A big rig navigating a stretch of windy Wyoming highway last week was blown over by high winds and landed on a Wyoming Highway Patrol cruiser. According to CBS News, three Wyoming Highway Patrol troopers responded to an accident along Interstate 80 near Elk Mountain on February 7. While the troopers were out of their cars assisting the crash victims, a white Volvo semi-truck lumbered up I-80 toward them. Wind gusts in that part of Wyoming were clocked in at up to 90 miles per hour on Tuesday, and one of them caught the semi as it neared the parked cruisers. Video from one of the cruiser's onboard cameras showed the big rig drift to the right as a big gust hit the trailer. Slowly, the whole rig tipped over and flattened one of the parked cruisers. The truck then slid a few feet on its side and came to a stop just aft of the cruiser. None of the troopers were injured in the incident, and two people in the truck came out of it unhurt as well. Patrol Lieutenant David Wagener told KGWN that that stretch of I-80 was closed on Tuesday to lightweight, high-profile vehicles. The truck driver was cited for the incident. High winds are no joke, and vehicles getting blown around or even clean off the road is a pretty common phenomenon. Way back in 2011, a truck got blown over in Utah. Then there was a train that got blown off a bridge in Louisiana in 2015. Related Video: News Source: CBS News, KGWN Auto News Dodge Volvo Driving Safety Truck Commercial Vehicles Police/Emergency Sedan semi truck rollover wyoming

Dodge recalls 27k Darts for bracket that can disrupt transmission module

Dodge is recalling 27,520 examples of the 2013-2015 Dart with dual-clutch gearboxes. The mounting bracket for the transmission control module can affect the part's operation and cause the compacts to suddenly shift into neutral. According to the automaker, 23,688 of them are in the US, 3,376 in Canada, 5 in Mexico, and 451 elsewhere. The National Highway Traffic Safety Administration reports these examples carry build dates between February 24, 2012, and June 16, 2015. There are also no reports of accidents or injuries. Because of the way the bracket is mounted, the part can put too much force on the control module's circuit board and cause it to shift out of gear. The engine and airbags remain operable if this happens. To fix things, dealers will install a redesigned mount and replacement module. Related Video: Statement: Mounting Bracket September 14, 2015 , Auburn Hills, Mich. - FCA US LLC is recalling an estimated 23,688 cars in the U.S. to replace certain control modules and mounting brackets that may contribute to a loss of motive power. The Company is unaware of any related injuries or accidents. An FCA US investigation prompted by a small number of warranty claims discovered a control-module mounting bracket may apply too much force and disrupt the function of a circuit board within the module. This condition, unique to certain cars equipped with dual dry-clutch transmissions (DDCT), may cause the transmission to shift into neutral. However, the engine remains on and the vehicle's air-bags, as well as other safety features, are unaffected. The condition may also be preceded by the illumination of a dashboard warning light. Customers who observe this are urged to contact their dealers. The campaign is limited to certain 2013-2015 Dodge Darts equipped with DDCTs. Additional vehicles will be recalled in Canada (3,376), Mexico (five) and outside the NAFTA region (451). Affected customers will be advised when they may schedule service, which will be performed free of charge. Service will entail installation of a redesigned mounting bracket and replacement of the control module. Customers with additional questions may call the FCA US Customer Information Center at 1-800-853-1403.

That thing got a Hemi? Mopar engine kits make it easier to say yes

Thanks to a new kit from Mopar, classic car owners will have an easier time dropping Hemis into their muscle cars. The kit works with Mopar's 345 and 392 Hemi engines (5.7 and 6.4 liters respectively) and with cars built before 1975. The kit will run $1,795 and has everything needed to get one of the above engines running. The parts include a power distribution system, engine computer, engine and chassis wiring harnesses, O2 and intake air temperature sensors, ground wiring and a gas pedal. The kit is also designed to work with a manual transmission, but Mopar says a transmission such as the Torqueflite 727 and 904 can be made to work with the system. As for examples of the kit in action, take a look at the Jeep CJ66 and Dodge Challenger Shakedown that Mopar revealed this week at the SEMA show. Mopar also offers a few other parts to help complete the project, including various oil pans to clear subframes, a set of headers, and accessory drives for power steering and air conditioning. All of these parts are extra cost though. You'll also need an engine, and the 345 starts at $6,070, and the 392 runs $9,335. However, if you happen to already have one from 2014 or newer, that will work, too. Muscle car fans are getting more choices for their engine conversions. Chevrolet Performance already sells crate engines with "Connect and Cruise" kits to get its engines working in classic cars. The General also offers it with more engines. However, for people who want to keep a Mopar engine in their classic Chrysler, Dodge, Plymouth, or Jeep, this is a cool new option. Related Video: Featured Gallery Mopar Hemi V8 Engine Swap Kit Image Credit: FCA Aftermarket SEMA Show Chrysler Dodge Performance Classics FCA engine swap SEMA 2016