*2008*ram 2500*4x4*quad Cab*6.7l Cummins Turbo Diesel*auto*short Bed*infinity* on 2040-cars

Auto blog

What's the deal with Chrysler demanding colleges crush their Vipers? [w/video]

Students and teachers at a Washington community college are up in arms following an order from Chrysler that it must destroy the pre-production Dodge Viper that was donated to the school's automotive technology program ten years ago.
The Viper in question is said to be the fourth off the production line, based on its VIN, and has had its emissions controls disabled, allowing its ten-cylinder engine to produce 600 horsepower, according to a report from Yahoo! Autos. As one of the first Vipers ever produced, the school's AT instructors claim it could be worth $250,000 in a museum, while a local news report purports that Jay Leno once tried to purchase the car, but the sale was prevented by Chrysler.
As pointed out by our friends at Autobytel, though, there are a lot of things in this story that don't quite add up. Immediately noticeable from the news report embedded below - which shows the car at South Puget Sound Community College - is that the car in question is not a 1992 model. When the Viper went on sale in 1992, it was only available as an RT/10 with a (flimsy) soft top, like the red car shown above. But the car featured in the report from KING5 News (inset image) is clearly a hardtop Viper GTS, which didn't enter production until 1996. And even if, as reported by a local newspaper, the hardtop featured is a prototype, it doesn't explain the lack of another iconic feature of the first Vipers - their distinctive side pipes. This kind of pokes holes in the school's argument that this is the fourth Viper to ever roll down the line. At best, this appears to be a pre-production Viper GTS.

Chrysler recalling 2009-2010 Ram 1500, Dodge Dakota pickups over axle pinion nut

Chrysler is issuing a recall for the 2009 and 2010 Ram 1500 and Dodge Dakota pickup trucks due to improper installation of the rear axle pinion nut. According to the National Highway Traffic Safety Administration, a total of 44,300 trucks are affected by the recall, and there have been 12 confirmed incidents including one crash.
The issue on both trucks is that the pinion nut is loosening on some trucks due to a lack of thread adhesive, and it is causing the rear axle to lock up resulting in loss of vehicle control. NHTSA's recall notice says that eight incidents occurred at speeds over 35 miles per hour and most also exhibited driveshaft failures as well since the loss of the pinion nut would cause the gear to separate from the driveshaft. In one complaint, the driveshaft separated from the rear axle and punctured the gas tank.
Chrysler will begin sending out recall notices to affected owners in November, but scroll down to see the official NHTSA notice.

Watch this Dodge Viper get clawed to death

There's a scene in the James Bond movie, Casino Royale, where Daniel Craig's Agent 007 is captured by villain Le Chiffre, played by Mads Mikkelsen. Le Chiffre tortures Bond in a scene that is rather difficult to watch (especially for blokes) and impossible to describe on these digital pages (Google at your own risk). This video is the automotive equivalent of the Casino Royale torture scene.
It shows a Dodge Viper - a late, first-generation GTS judging by the center-exit exhausts - getting assaulted by a giant piece of heavy equipment. The large claw shows no mercy on the V10-powered sports car, rending its muscular curves into pieces and then running it over, just for good measure. It's a painful video to watch (and hear!), made worse because we don't know what the Viper did to deserve such a fate. About a third of the way through the video, the cameraman indicates that the man with the claw is a new operator from Chrysler, and it appears there may be some fire damage, but beyond that, we don't have much to go on.
Scroll down for the video but be warned, it isn't for the faint of heart.