No Reserve 93k Miles Crew Cab 4x4 Short Bed 1500 02 04 05 06 Silverado F-150 on 2040-cars

Auto blog

Chrysler recalling 278,222 trucks and SUVs over bad rear axles

Chrysler has issued a recall of 278,222 light trucks and sport utility vehicles here in the United States. The reason: bad rear axles. Specifically, according to the National Highway Traffic Safety Administration, the rear axle pinion nut may lack a necessary adhesive patch, which could cause the nut to loosen. If this happens, the axle can lock up, which could cause all sorts of havoc on the road.
This is an expansion of the rear axle recall announced in October of last year, where 44,300 Ram 1500 and Dodge Dakota models were being called in. At that time, 12 accidents had been reported due to the faulty axle pinion nut.
Affected vehicles include Ram 1500 trucks from the 2009 to 2012 model years, Dodge Dakota models from the 2009 to 2011 model years, and both the Chrysler Aspen and Dodge Durango SUV twins, both from the 2009 model year only.

2013 Dodge Durango R/T

Not too long ago, Chevrolet got itself into some trouble by throwing the SS badge on just about everything it produced, so I've always been a little hesitant about the seemingly excessive use of the R/T nameplate on Dodge vehicles. For the 2013 model year, every model in Dodge's lineup has an R/T trim level from Dart all the way up to the Durango. Although the R/T name used to signified models made for road and track, I doubt anyone would be delusional enough to assume the Durango - and some of the other models wearing this badge - are suited for any sort of track duty.
Still, when this 2013 Dodge Durango R/T rolled up for me to drive for the week, I couldn't help but take in its big, mean and imposing stance. Sure, if I had my choice of buying any of the Dodge R/T products, the Charger and Challenger would be my top picks for sure, but it's easy to say that the Durango would be a close third - far above the R/T versions of the Avenger, Journey and Grand Caravan.
Driving Notes

Mopar unveils Dodge Challenger Drag Pak [w/video]

Dodge is going drag racing, and it's doing it with an all-new version of the Challenger for NHRA's Sportsman class. FCA's Mopar parts and performance arm announced the new Challenger Drag Pak Friday, showing off a version with a 354-cubic-inch (that's a 5.8-liter, by the way), supercharged V8 and a 426-ci (7.0-liter), naturally aspirated V8 – both Hemis, of course – that can get the big coupes through the quarter-mile in "the eight-second range." While the two engines deliver similar performance, at their base, they're quite a bit different. The supercharged model uses a cast-iron block, while the 426 has aluminum for both the block and head. That said, both models get customized engine calibrations, and are mated to unique, race-spec automatic transmissions. But drag racing is about far more than just outright power. Mopar significantly updated the four-link rear suspension, adding a four-inch rear axle from Strange Engineering, along with an aluminum, nine-inch third member, while the rear-axle housing has been strengthened in general. Both the rear shocks and front struts can be adjusted for rebound and compression, too. Lightweight 15-inch wheels, meanwhile, are shod in super-sticky Hoosier drag radials, with nine inches of tread in back and 4.5 inches in front. The new Challenger Drag Pak should run the quarter-mile in "the eight-second range." In the cabin, there's an NHRA-spec roll cage, a Racepak gauge cluster, and a handsome pair of Sparco racing seats. Outside, supercharged models get blue decals, while naturally aspirated varieties get black stickers, although there's more to the new Challenger dragster's exterior than just its decals. Mopar tweaked the big-scoop hood, promising it's easier to get up to check on the engine, and the designers also added trailer tie-down straps in both the front and rear. While the dragster was the big news today, Mopar officials also announced the two enhanced Scat Pack kits for both the Dodge Charger and Challenger R/T. The 5.7-liter Hemi models gain an extra 56 horsepower and 30 pound-feet of torque in the Scat Pack 2 thanks to a new cam, valve springs, pushrods, and gaskets. The Scat Pack 3, meanwhile, adds 75 hp and 44 lb-ft, on top of the gains from the lower packages. That should be perfect for drivers who wish to snort in the face of their SRT 392-driving friends. The third stage adds a ported cylinder heads, as well as high-flow manifolds and catalysts.