2011 Dodge Ram 1500 Slt R/t 4x4 Automatic 4-door Truck on 2040-cars

Auto blog

2015 Dodge Challenger SRT Hellcat [w/videos]

Darrell Waltrip once said, "If the lion didn't bite the tamer every once in a while, it wouldn't be exciting." The sentiment behind that aphorism is causing my adrenal gland to wake up as Dodge and SRT drivers and engineers - somber-faced to a man - give me the track talk that will precede my driving the 2015 Dodge Challenger SRT on the circuit at Portland International Raceway. PIR might not be Daytona, and the 707-horsepower Challenger Hellcat might seem tame to a legend like ol' Jaws, but there's a not-small part of me that's thinking about how hard Dodge's fire-breathing kitty might bite.
Just a few hours previous, I'd gotten behind the wheel of the Hellcat for the first time, letting its hyperbole-spitting, supercharged V8 Hemi pull me yieldingly through Portland's morning commuter traffic. Lulled into a cocky certainty by the Challenger's good manners at low speed, I drove the throttle just a hair too deep, too fast when I ran on to the highway ramp. For just an instant the rear tires were utterly drenched in torque, and the back end of the big Dodge loosened up like a drift car on a wet track. Throttle steer lives at the fleeting whim of your right foot in this car.
It was no big thing to lay off the gas and pull the Hellcat back in line as I entered the highway, but the incident did get me to thinking: What will this car do to me on a road course?

VLF Force 1 V10 is a rebodied Viper priced like a Lamborghini

It would appear that Henrik Fisker is done with hybrids. His latest project, called the Force 1, packs an oversized V10 engine with no electric assist in sight and all the environmental credentials of a herd of flatulent cattle. Alongside the Karma-based, Corvette-powered Destino, the Force 1 is the second product from VLF Automotive. Fisker has taken partnership in the new firm as chief designer alongside chairman Bob Lutz and CEO Gilbert Villarreal. The company isn't saying explicitly what the Force 1 is based on, but it doesn't take a CSI team to trace its roots back to the Dodge Viper. Never mind that it's being built in Auburn Hills – the same Detroit suburb where Chrysler is headquartered – or that it was jointly developed by Fisker and professional Viper racer and dealer Ben Keating. It also happens to be powered by an 8.4-liter V10, and there aren't many of those kicking around the industry. Instead of the Viper's 645 horsepower and 600 pound-feet of torque, the Force 1's ten-cylinder engine is optimized to deliver 745 hp and 638 lb-ft. That, according to VLF, is enough to send the coupe rocketing to 60 in 3.0 seconds flat, covering the quarter-mile in under 11 seconds on its way to a top speed of 218 miles per hour. The power is transmitted to the Pirelli PZero rubber through a six-speed manual, but VLF says it will fit it with an automatic at the customer's request. Around that massive engine and two-seat cockpit, Fisker designed a new shape that, for better or for worse, looks way more aggressive than the Viper's. The Force 1's proportions are tellingly super-snake, but the curves are replaced by some very angry-looking angles and vents. Its head- and taillights are ultra thin, and the deep-dish, split-four-spoke wheels seem to visually split the difference between the three-spoke wheels on the original Viper and the five-spoke alloys it wears today. If you doubted the Force 1's origins before, the interior ought to give it away, with its wide tunnel and familiar surfaces. Only VLF has refinished it in leather, suede, and Alcantara, all diamond stitched with contrasting thread to help position this as a more luxurious prospect than the Dodge. It even fit between the seatbacks place for two champagne bottles that we hope nobody would consider consuming before trying to handle that much power. Of course, none of this will come cheap.

FCA plants skipping summer shutdown to keep up with demand

Hopefully, some FCA US factory employees don't have big plans for the usual summer shutdown, because the automaker is keeping several plants running this year. Demand is so high that the company wants to keep models rolling off the assembly lines. Four FCA US assembly plants, all the engine factories, and some locations that build transmissions are staying open throughout the summer, according to the Detroit Free Press. Usually, these sites would see a two-week shutdown for the company to retool and perform repairs. This year, factories are staying open for FCA to support its strong sales. The lines that remaining humming through the summer show an inclination toward the automaker's popular SUV's and crossovers. They include the Jefferson North Assembly Plant in Michigan that builds the Jeep Grand Cherokee and Dodge Durango; Saltillo Van Assembly in Mexico that constructs the Ram ProMaster; Toledo Assembly Complex in Ohio that produces the Cherokee and Wrangler; and Toluca Assembly in Mexico that makes the Dodge Journey and Fiat 500. Related Video: News Source: The Detroit Free PressImage Credit: Bill Pugliano / Getty Images Plants/Manufacturing Dodge Fiat Jeep RAM FCA dodge journey fca us ram promaster Jefferson North Assembly Plant