1999 Dodge Ram 1500 4x4 Ext Cab on 2040-cars

Auto blog

Will the Chrysler 300 go front-wheel drive?

FCA chief executive Sergio Marchionne hinted last week that the strapping rear-wheel-drive Chrysler 300 sedan could go front-wheel drive for its next generation using the underpinnings from the Chrysler Pacifica minivan. Speaking at the Pacifica's production launch in Windsor, ON, Marchionne said, "this plant and this architecture is capable of making the 300 successor, the front-wheel, all-wheel-drive successor," Reuters reported. Perhaps realizing he appeared to be announcing a dramatic shift in product strategy, Marchionne backpedaled in response to a follow-up question, noting only that the Ontario factory is "capable" of making the sedan. "It's capable. It's not a commitment," he said, according to Reuters. The 300 is currently built in Brampton, ON, alongside the mechanically similar Dodge Charger and Challenger. The platform, known as LX in enthusiast circles, is an evolution of Mercedes-based chassis pieces that date to the DaimlerChrysler era. Marchionne's comments didn't cover the Dodges and left a lot open to interpretation. The 300 could switch to front- and all-wheel-drive and focus on a more civilized, elegant ride character, leaving the Charger and two-door Challenger as traditional rear-wheel-drive muscle cars. That strategy would further differentiate the Chrysler and Dodge car lines. Additionally, the Charger's RWD platform makes it a popular police vehicle, and both Dodges are offered in top trim as 707-horsepower Hellcats. Switching to front-wheel drive would seemingly complicate both of those endeavors. Rumors have also swirled that Alfa Romeo could contribute RWD underpinnings for Dodge. Related Video: Featured Gallery 2015 Chrysler 300 View 92 Photos Design/Style Chrysler Dodge Off-Road Vehicles Performance Sedan chrysler pacifica

Man hits 153 mph on I-75 in Dodge Magnum

A man driving in Michigan took his 2005 Dodge Magnum practically to the limit in the wee hours of the morning on May 19 when the Michigan State Police caught him on radar going 153 miles per hour on Interstate 75 near Detroit. The 21-year-old driver was spotted around 3:00 AM, according to The Detroit News. Michigan State Police First Lieutenant Michael Shaw told Autoblog that officers initially saw the man on radar doing 79 mph in a 70-mph-zone, and they started following him. He eventually clocked 153 mph. However, First Lt. Shaw was clear that there was never a pursuit. "Speeding isn't necessarily a reason to put the public at risk," he said. The situation ended rather abruptly, though. The driver pulled off the interstate and behind a building. He remained in the vehicle, and police arrived and arrested him. According to First Lt. Shaw, the man was driving home from work and alcohol wasn't a factor. The Magnum has been impounded, and the driver was charged with reckless driving. Unfortunately, First Lt. Shaw said that he didn't know what engine was in the wagon, but as enthusiasts, we're curious. After all, the 2005 Magnum RT was governed to 130 mph and the SRT8 wasn't unleashed until 2006, which means either the wagon must've been derestricted to hit such high speeds or that police have the year wrong. We'll let you know if we figure that one out...

Dodge Durango Shaker concept: A 392 V8 in front of six Viper seats

When done right, a parts-bin special can be a beautiful thing. This Dodge Durango Shaker concept for the 2016 SEMA show is one such vehicle, and it's easily our favorite Mopar debuting in Vegas. The key, of course, is pulling from the right bins. Take a tour and you'll see Charger, Challenger, and Viper pieces grafted onto this slick crossover. The featured special part is the big, 6.4-liter 392 Hemi V8 that's been dropped under the hood; it's sourced from the SRT Challenger and Charger where it makes 485 horsepower and 475 pound-feet of torque. With that in place, the fabricators cut a big hole in that hood for the Challenger's awesome optional shaker scoop. It wasn't an easy installation; it required a custom spacer for the intake to make sure everything lined up with the hole properly. View 17 Photos Apparently there were some Viper seats lying around, so six of them were stuck into this Durango. Makes sense. It does lose a bit of people-carrying capability as a result, since only two seats fit in each row, and the seats don't fold for extra cargo room. A Dodge spokesperson attested to the fact that all three rows are usable, if not totally comfortable. But then stock third-row seats aren't always that comfortable anyway. Seriously, though, Viper seats. We don't care how comfortable or usable the result is. Although you might not give it a second thought, even the fuel filler needed some special attention. This piece was also lifted from a Dodge Challenger, and it was taken along with the surrounding sheet metal. Because of the different orientation of the filler cover on the Challenger, the builders decided the easiest way to get it to fit was to chop the fuel filler section out and weld it onto the Durango. The designers also put a little blue Stig on the cover. And those are just the cool parts that were hard to install. This Durango features plenty of other slick details, like the custom bumpers, fender flares, and side skirts. Everything is painted B5 Blue with matte black and carbon accents all around. Up front, the bumper hides a pair of fog lights stolen from a Challenger Hellcat – and yes, they're the ones with intakes in the middle. The grille is also a custom piece, losing the standard crosshair design for better airflow. The fender flares cover up some seriously wide, 305-section tires at all four corners, which are hauled down by Hellcat brakes. The rear bumper bumper contains a stylish center-exit exhaust with dual tips.