1979 Dodge Little Red Express 86k.miles Runs And Looks Good Must See.. on 2040-cars

Auto blog

FCA recalls 894k total vehicles worldwide in two campaigns

FCA is recalling a total of 893,698 vehicles worldwide in two campaigns to fix problems with inadvertent airbag deployment, failure of the anti-lock brakes, and stability control systems in the Jeep Grand Cherokee, Liberty, Dodge Journey, and Fiat Freemont. 559,703 of these vehicles are in the US. The larger recall affects 284,089 examples of the 2003 Jeep Liberty and 2004 Jeep Grand Cherokee, and there are also 13,411 of them in Canada, 6,277 in Mexico, and 48,212 outside the NAFTA region. Because of "electrical noise beyond the tolerance of the airbag electronic control module", part of that component can fail, according to the National Highway Traffic Safety Administration. This can cause the front and side airbags to deploy and the seatbelt pre-tensioners to activate inadvertently. FCA US has seven reports of alleged injuries from this problem. To fix the situation, the Jeeps need their Occupant Restraint Control modules replaced, as well as the front- and side-impact sensors. According to the NHTSA, the replacement parts won't be available until early 2016. Still, FCA US will advise owners about the problem in a letter by the end of December and will send a second notification when the components are ready. The second campaign affects 275,614 examples of the 2012-2015 Dodge Journey in the US; plus 78,148 of them in Canada, 36,471 in Mexico, and 151,476 left-hand drive units outside of NAFTA where it's sold as the Fiat Freemont. On these vehicles, water intrusion can disable the anti-lock brakes and electronic stability control, although a warning light often illuminates when this issue occurs, and the problem doesn't affect regular braking. There are also no reports of injuries or accidents. To fix the issue, dealers will seal the ABS wiring harness and will replace any already affected components as necessary, like the ABS module or the headlamp and dashboard wiring harness. Statement: Occupant Restraint Control Modules October 30, 2015 , Auburn Hills, Mich. - FCA US LLC is voluntarily recalling an estimated 284,089 older-model SUVs in the U.S. to replace their Occupant Restraint Control (ORC) modules and front and/or side-impact sensors, as required. Within this vehicle population, FCA US became aware of seven injuries caused by inadvertent air-bag deployments and advised NHTSA accordingly. The affected vehicles are not equipped with Takata Corp. air-bags. The Company is unaware of any related accidents.

Mopar unveils Dodge Challenger Drag Pak [w/video]

Dodge is going drag racing, and it's doing it with an all-new version of the Challenger for NHRA's Sportsman class. FCA's Mopar parts and performance arm announced the new Challenger Drag Pak Friday, showing off a version with a 354-cubic-inch (that's a 5.8-liter, by the way), supercharged V8 and a 426-ci (7.0-liter), naturally aspirated V8 – both Hemis, of course – that can get the big coupes through the quarter-mile in "the eight-second range." While the two engines deliver similar performance, at their base, they're quite a bit different. The supercharged model uses a cast-iron block, while the 426 has aluminum for both the block and head. That said, both models get customized engine calibrations, and are mated to unique, race-spec automatic transmissions. But drag racing is about far more than just outright power. Mopar significantly updated the four-link rear suspension, adding a four-inch rear axle from Strange Engineering, along with an aluminum, nine-inch third member, while the rear-axle housing has been strengthened in general. Both the rear shocks and front struts can be adjusted for rebound and compression, too. Lightweight 15-inch wheels, meanwhile, are shod in super-sticky Hoosier drag radials, with nine inches of tread in back and 4.5 inches in front. The new Challenger Drag Pak should run the quarter-mile in "the eight-second range." In the cabin, there's an NHRA-spec roll cage, a Racepak gauge cluster, and a handsome pair of Sparco racing seats. Outside, supercharged models get blue decals, while naturally aspirated varieties get black stickers, although there's more to the new Challenger dragster's exterior than just its decals. Mopar tweaked the big-scoop hood, promising it's easier to get up to check on the engine, and the designers also added trailer tie-down straps in both the front and rear. While the dragster was the big news today, Mopar officials also announced the two enhanced Scat Pack kits for both the Dodge Charger and Challenger R/T. The 5.7-liter Hemi models gain an extra 56 horsepower and 30 pound-feet of torque in the Scat Pack 2 thanks to a new cam, valve springs, pushrods, and gaskets. The Scat Pack 3, meanwhile, adds 75 hp and 44 lb-ft, on top of the gains from the lower packages. That should be perfect for drivers who wish to snort in the face of their SRT 392-driving friends. The third stage adds a ported cylinder heads, as well as high-flow manifolds and catalysts.

Dodge Scat Pack for 5.7L Hemi V8 detailed, priced

Dodge revived the Scat Pack name back in November at the 2013 SEMA show. At the time, though, we were short of details on forthcoming upgrade packages, which were destined to add some oomph to the Challenger, Charger and Dart. We're still waiting to hear about the upgrades to the Dart's 2.4-liter four-pot, but Dodge has gone ahead and released the details on the upgrades to the 5.7-liter Hemi V8 in the Challenger and Charger R/T.
As we detailed in our original post, three different Scat Packs will be available that will allow customers to upgrade their cars without voiding the warranties. Starting with the $2,195 Stage 1 kit, owners will net an extra 18 horsepower and 18 pound-feet of torque thanks to a Mopar-branded cold-air intake, exhaust and ECU ref lash. Stage 1 is also the only package that could be installed outside of a Chrysler-authorized service center without voiding the warranty (a mechanically competent owner could even do it at home, we're told by Dodge). Stage 2 builds on the entry level Scat Pack, and adds performance camshaft kit, which boosts output over the stock 5.7 by up to 30 hp for $1,895. As with the Stage 1, the ECU is tweaked.
For those that want to go whole hog, they can add the Stage 3 for $4,995. The top-tier gets quite serious, adding CNC-ported cylinder heads, as well as high-flow headers and cats. Output over stock is 58 hp and 47 lb-ft of torque. Each kit comes with a pair of badges, just in case owners want a bit of visual flair.