1952 Dodge 2.5 Ton Job Rated Dump on 2040-cars

Auto blog

Fiat Chrysler to get $105M fine from NHTSA for recall woes

The National Highway Traffic Safety Administration is about to send a powerful message to automakers doing business in the United States, assuming reports of an upcoming $105 million fine against Fiat Chrysler Automobiles comes to fruition. In addition to the record-setting monetary fine, according to The Wall Street Journal, FCA will have to accept an independent auditor that will monitor the company's recall and safety processes and will be forced to buy back certain recalled vehicles. In other cases, such as with Jeep Grand Cherokee and Liberty models with gas tanks that could potentially catch fire in certain types of accidents, FCA will offer financial encouragement for owners to get their recall work done or to trade those older vehicles in on new cars, according to the report. FCA could reportedly reduce its fines if it meets certain conditions, though those remain unclear at this time. These actions against FCA are being taken after NHTSA began a probe into the automaker over almost two dozen separate instances where the government claims FCA failed to follow proper procedures for recalls and safety defects. Included in those safety lapses are more than 11 million vehicles currently in customer hands. These penalties and fines are separate from the investigation over security problems with Chrysler's Uconnect system that allowed hackers to obtain remote access into key vehicle systems in 1.4 million vehicles. Related Video: Image Credit: Marco Bertorello/AFP/Getty Earnings/Financials Government/Legal Recalls Chrysler Dodge Fiat Jeep RAM Safety fiat chrysler automobiles fine

Dodge Demon makes so much torque, it needs stronger driveline parts

Torque is a lovely thing, a sweet and wonderful force that twists and pulls and can help propel a two-ton metal box forward at comical speeds. Torque is also fickle and will bend and break those same metal parts without a second thought, which is why the new Dodge Demon is compensating for its increased torque with some new re-engineered and reinforced parts. And there's software intended to combat wheel hop, which one of the most dramatic ways torque can break stuff. Week 8's video, "Race-hardened Parts," gives a hint towards what all these new parts can do. While we still don't know how much torque the Demon will throw out, we do know it's enough to warrant an upgraded prop shaft, half shafts, and a differential housing. The Challenger Hellcat, which is the basis for the Demon, makes 650 pound-feet of torque already. The new parts will go a long way toward making sure the work from the Demon's engine is properly translated into motion by those Nitto drag radials. The new prop shaft uses high-strength steel, heat-treated stub-shafts, and increases the tube thickness by 20 percent for a 15 percent increase in torque capacity. Additionally, Dodge says the upgraded differential housing allows for a 30 percent increase in torque capacity by using heat-treated A383 aluminum alloy and a higher strength shot-peened gear set. The 41-spline half shafts that deliver 20 percent increased torque capacity through the use of high-strength low alloy steel and 8-ball joints. In addition to the hardware, the Launch Assist software has been tuned to help alleviate wheel hop. Dodge says the Demon is the first factory production car that uses wheel speed sensors to detect hop and momentarily cut torque to compensate. This means a driver can keep their foot planted on the floor while the computer sorts out the traction. Previously, the best solution was to back off the throttle to manually cut the load. Finally, the Dodge Demon will offer a four-point harness mounting bar as an optional accessory. The part will be supplied by Speedlogix and fits in place of the deleted rear seat. Customers can install the bar without having to hack apart their cars to find a proper mounting point. Look for more teasers and info on ifyouknowyouknow.com in the lead-up to the Demon's debut at the 2017 New York Auto Show. Related Video: Image Credit: FCA Dodge Performance dodge demon dodge hellcat

Dodge Challenger SRT Hellcat #0001 raises $825,000 for charity

$60,000 doesn't strike us as a lot to pay for a muscle car with 707 horsepower on tap. $825,000... now that's a different story. But, according to the official SRT blog, that's how much one generous and eager buyer paid for the privilege of getting his (or her) hands on the very first new Dodge Challenger SRT Hellcat.
Decked out in Stryker Red paint that's usually reserved for the Viper, the supercharged Challenger bearing the VIN 0001 went up for auction at the Mandalay Bay hotel and casino in Las Vegas on Saturday under the auspices of Barrett-Jackson. By the time bidding ended, the gavel dropped at $825,000 - nearly 14 times the sticker price - 100 percent of which will benefit Opportunity Vehicle, a charity that aids the intellectually handicapped in the Las Vegas Area.