2009 Dodge Nitro Se Sport Utility 4-door 3.7l on 2040-cars

Auto blog

Dodge Durango Shaker concept: A 392 V8 in front of six Viper seats

When done right, a parts-bin special can be a beautiful thing. This Dodge Durango Shaker concept for the 2016 SEMA show is one such vehicle, and it's easily our favorite Mopar debuting in Vegas. The key, of course, is pulling from the right bins. Take a tour and you'll see Charger, Challenger, and Viper pieces grafted onto this slick crossover. The featured special part is the big, 6.4-liter 392 Hemi V8 that's been dropped under the hood; it's sourced from the SRT Challenger and Charger where it makes 485 horsepower and 475 pound-feet of torque. With that in place, the fabricators cut a big hole in that hood for the Challenger's awesome optional shaker scoop. It wasn't an easy installation; it required a custom spacer for the intake to make sure everything lined up with the hole properly. View 17 Photos Apparently there were some Viper seats lying around, so six of them were stuck into this Durango. Makes sense. It does lose a bit of people-carrying capability as a result, since only two seats fit in each row, and the seats don't fold for extra cargo room. A Dodge spokesperson attested to the fact that all three rows are usable, if not totally comfortable. But then stock third-row seats aren't always that comfortable anyway. Seriously, though, Viper seats. We don't care how comfortable or usable the result is. Although you might not give it a second thought, even the fuel filler needed some special attention. This piece was also lifted from a Dodge Challenger, and it was taken along with the surrounding sheet metal. Because of the different orientation of the filler cover on the Challenger, the builders decided the easiest way to get it to fit was to chop the fuel filler section out and weld it onto the Durango. The designers also put a little blue Stig on the cover. And those are just the cool parts that were hard to install. This Durango features plenty of other slick details, like the custom bumpers, fender flares, and side skirts. Everything is painted B5 Blue with matte black and carbon accents all around. Up front, the bumper hides a pair of fog lights stolen from a Challenger Hellcat – and yes, they're the ones with intakes in the middle. The grille is also a custom piece, losing the standard crosshair design for better airflow. The fender flares cover up some seriously wide, 305-section tires at all four corners, which are hauled down by Hellcat brakes. The rear bumper bumper contains a stylish center-exit exhaust with dual tips.

NHTSA investigating power modules on Chrysler Group SUVs and minivans

The Center for Auto Safety is officially petitioning the National Highway Traffic Safety Administration to begin scrutinizing alleged problems with the totally integrated power module (TIPM) on about 24 Chrysler Group SUVs and minivans. The advocacy group claims that the part's failure can cause affected vehicles to stall or not start at all. NHTSA is still looking into the accusations and deciding whether a full investigation is actually warranted.
The CAS petition claims at least 70 TIPM failures, but according to NHTSA, six of the complaints are for models that don't have the modules. In 34 of the reported cases, the vehicles refused to start, and in 17 of them the engine stalled. There were also two allegations of smoke and one of a fire. However, none of these affected airbag deployment or resulted in a crash.
This petition isn't the first TIPM-related problem for Chrysler Group. A recent report in the New York Times alleged that it found 240 complaints potentially related to the issue on NHTSA's website alone. In September, the automaker also recalled 230,760 examples worldwide (188,723 in the US) of the 2011 Jeep Grand Cherokee and Dodge Durango replace the fuel pump relay circuit inside of the TIPM-7 with one external to the unit. The original part could allegedly cause the models to stall without warning. Even earlier, the company also recalled about 80,000 examples of the Jeep Wrangler and Dodge Nitro in 2007 to have the module reprogrammed.

Dodge Charger Hellcat makes 1,032 hp with Hennessey help

Sometimes you just want four doors. Earlier this week we brought you Hennessey's riff on the Dodge Challenger Hellcat. Now comes the Charger. Much like its two-door sibling, the Charger gets boosted to as much as 1,032 hp and 987 lb-ft of torque (at the crank) thanks to the addition of a twin-turbocharging setup that works with the factory supercharger. The turbo headers and downpipes are stainless steel, and there is a high-flow air-to-water intercooler and dual-turbo waste gates. Hennessey also beefs up the fuel injectors, fuel pump, and the rest of the fuel system. The engine management system and chassis are recalibrated to accommodate all of this. You also get numbered plaques signed by John Hennessey, the boss of the Texas tuning outfit, and the technician who does your build. Hennessey's additions result in zero-to-60 mph sprints in 2.7 seconds, and the big sedan can run the quarter mile in 9.9 seconds at 142 mph. Like the Challenger, the Charger has the same disclaimer: the lofty horsepower figure comes from an engine dyno, and it will be a 15-to 20-percent lower at the rear wheels. Related Video: Image Credit: Hennessey Performance Dodge Performance Sedan Hennessey dodge charger hellcat