5.7l V8 Hemi Slt Lone Star Lifted Off Road Tires 20in Rims Uconnect Mp3 Dvd 4x4 on 2040-cars

Auto blog

Race Recap: Rolex 24 at Daytona was fast and feisty

Let the record show that victory at the 2015 Rolex 24 at Daytona went to the No. 02 Chip Ganassi Racing with Felix Sabates Target/Ford EcoBoost Riley DP driven by Verizon IndyCar drivers Scott Dixon and Tony Kanaan and NASCAR drivers Jamie McMurray and Kyle Larson. The winner did 740 laps to cover 2,634.3 miles in 24 hours and 57.667 seconds. That's a statement to this year's pace in spite of 18 cautions, two more than last year: the Michael Shank Racing Ligier got pole with a time of 1:39.194, slower than last year's pole time of 1:38.270; however, the winning car last year only did 695 laps. The fight for top honors was shaved to a four-car battle over the first third of the event. The No. 02 Ganassi car took the lead on the first lap, swapping it well into the night with the No. 01 Ganassi car, the No. 10 Wayne Taylor Racing Corvette DP, and the defending champion No. 5 Action Express Corvette DP, all of them staying within about 20 seconds of one another. The Action Express car had a fuel connector come loose and lost three laps getting towed back to the pits to have it reattached, but was back in the lead 18 hours in. The No. 01 Ganassi car dropped out with recurring clutch problems 22 hours in, retiring not long after. A race-within-the-race is where the concluding action happened, a seven minute, 30-second dash from the end of the last caution to the checkered flag. During the penultimate pit stops with an hour to go, Dixon was in second place followed Jordan Taylor in the Wayne Taylor Racing DP into the pits but beat him out, taking the lead. The Action Express car was in third. In the last pit stops of the race, Dixon gained even more time, getting a four-second advantage over Taylor. Then a full-course caution came out twenty minutes before the finish when a Prototype Challenge car hit the wall and caught fire, bunching up the field. That closed the pits, but the Wayne Taylor Racing car had to pit during that yellow because of a miscalculation of driver time. No driver can be behind the wheel for more than four hours in a six-hour period but Jordan Taylor was going to go over, so he came in to swap out for brother Ricky. That cost the team any chance of second place, since they took an additional drive-through penalty for entering closed pits. When the track went green again, Sebastien Bourdais in the Action Express car stayed all over Dixon for the final five laps but couldn't get around him.

That thing got a Hemi? Mopar engine kits make it easier to say yes

Thanks to a new kit from Mopar, classic car owners will have an easier time dropping Hemis into their muscle cars. The kit works with Mopar's 345 and 392 Hemi engines (5.7 and 6.4 liters respectively) and with cars built before 1975. The kit will run $1,795 and has everything needed to get one of the above engines running. The parts include a power distribution system, engine computer, engine and chassis wiring harnesses, O2 and intake air temperature sensors, ground wiring and a gas pedal. The kit is also designed to work with a manual transmission, but Mopar says a transmission such as the Torqueflite 727 and 904 can be made to work with the system. As for examples of the kit in action, take a look at the Jeep CJ66 and Dodge Challenger Shakedown that Mopar revealed this week at the SEMA show. Mopar also offers a few other parts to help complete the project, including various oil pans to clear subframes, a set of headers, and accessory drives for power steering and air conditioning. All of these parts are extra cost though. You'll also need an engine, and the 345 starts at $6,070, and the 392 runs $9,335. However, if you happen to already have one from 2014 or newer, that will work, too. Muscle car fans are getting more choices for their engine conversions. Chevrolet Performance already sells crate engines with "Connect and Cruise" kits to get its engines working in classic cars. The General also offers it with more engines. However, for people who want to keep a Mopar engine in their classic Chrysler, Dodge, Plymouth, or Jeep, this is a cool new option. Related Video: Featured Gallery Mopar Hemi V8 Engine Swap Kit Image Credit: FCA Aftermarket SEMA Show Chrysler Dodge Performance Classics FCA engine swap SEMA 2016

2013 Dodge Dart gets all Moparized

Last year, Chrysler announced it would be offering more than 150 Mopar parts and accessories on the 2013 Dodge Dart, and we got a look at some of these parts firsthand at the Chicago Auto Show. Showing off all the optional parts at once would surely create a gaudy monstrosity, so Chrysler chose to equip this particular Dart GT with just a handful of Mopar goodies, which still gave the car a nice and tasteful custom look that is available straight from the dealership (and with a full warranty, too).
Decked out in a factory color called Header Orange Clear Coat - also a very appropriate show car hue - this car added exterior styling parts such as the vented, carbon fiber hood, the bolt-on front chin spoiler and a matte black decklid spoiler. Looking inside the car, you'd think the red-accented interior is part of the Mopar parts bin, too, but this is actually what the standard Dart GT cabin will look like when it goes on sale.