2014 Sxt New 3.6l V6 24v Fwd Suv Premium on 2040-cars

Auto blog

2013 Dodge Challenger V6 recalled for fire risk, owners asked not to drive

Chrysler has issued a recall for the V6 version of the 2013 Dodge Challenger (as pictured above in 2012MY) over the possibility of a wiring harness that could short circuit and lead to a fire. Owners of these V6 Challengers built from November 2012 through January 2013 are being urged to contact dealers immediately and, in the meantime, not to drive their cars or park in or near any buildings.
Chrysler estimates around 2,500 potentially affected Challengers are in owners' hands, while another 1,900 are still sitting on dealer lots. The total number of recalled vehicles is 4,459.
So far, Chrysler says that seven fires have been reported - none resulting in injuries. The company is instructing vehicle owners to contact their dealer to find out if their vehicle is included in the recall, but owners can also find the build date information of their vehicle by checking the label in the driver's door jamb.

2015 Ford Mustang vs. Camaro and Challenger [w/poll]

The horsepower wars are tightening among the Detroit Three, as the Ford Mustang, Chevrolet Camaro and Dodge Challenger are getting bigger, more powerful, and yes, more fuel efficient.
That came into sharper focus this week as more information was revealed about the most insane Challenger ever - the 707-horsepower Hellcat - followed quickly by Ford's in-depth showcase of the 2015 Mustang in Dearborn.
It's shaping up to be a golden age for enthusiasts, and what's under the hood is becoming more important than ever.

Mopar unveils Dodge Challenger Drag Pak [w/video]

Dodge is going drag racing, and it's doing it with an all-new version of the Challenger for NHRA's Sportsman class. FCA's Mopar parts and performance arm announced the new Challenger Drag Pak Friday, showing off a version with a 354-cubic-inch (that's a 5.8-liter, by the way), supercharged V8 and a 426-ci (7.0-liter), naturally aspirated V8 – both Hemis, of course – that can get the big coupes through the quarter-mile in "the eight-second range." While the two engines deliver similar performance, at their base, they're quite a bit different. The supercharged model uses a cast-iron block, while the 426 has aluminum for both the block and head. That said, both models get customized engine calibrations, and are mated to unique, race-spec automatic transmissions. But drag racing is about far more than just outright power. Mopar significantly updated the four-link rear suspension, adding a four-inch rear axle from Strange Engineering, along with an aluminum, nine-inch third member, while the rear-axle housing has been strengthened in general. Both the rear shocks and front struts can be adjusted for rebound and compression, too. Lightweight 15-inch wheels, meanwhile, are shod in super-sticky Hoosier drag radials, with nine inches of tread in back and 4.5 inches in front. The new Challenger Drag Pak should run the quarter-mile in "the eight-second range." In the cabin, there's an NHRA-spec roll cage, a Racepak gauge cluster, and a handsome pair of Sparco racing seats. Outside, supercharged models get blue decals, while naturally aspirated varieties get black stickers, although there's more to the new Challenger dragster's exterior than just its decals. Mopar tweaked the big-scoop hood, promising it's easier to get up to check on the engine, and the designers also added trailer tie-down straps in both the front and rear. While the dragster was the big news today, Mopar officials also announced the two enhanced Scat Pack kits for both the Dodge Charger and Challenger R/T. The 5.7-liter Hemi models gain an extra 56 horsepower and 30 pound-feet of torque in the Scat Pack 2 thanks to a new cam, valve springs, pushrods, and gaskets. The Scat Pack 3, meanwhile, adds 75 hp and 44 lb-ft, on top of the gains from the lower packages. That should be perfect for drivers who wish to snort in the face of their SRT 392-driving friends. The third stage adds a ported cylinder heads, as well as high-flow manifolds and catalysts.