2003 Dodge Grand Caravan Ex Mini Passenger Van 4-door 3.8l on 2040-cars

Auto blog

A look at the Dodge Demon's drag settings, modes, and go-fast tech

In the same video that gave us a peek at the 2018 Dodge Challenger SRT Demon's performance stats, there's a serious dump of info on the tech and tools that will likely help this muscle coupe slaughter drag strips. Dodge has outlined a few of them for us and we're using the power of inference to figure out the rest. Here's what we've gathered. A lot of these hints come from the Demon's version of Performance Pages, the infotainment screens that show what SRT models are doing and let the driver change the powertrain and chassis setup. There are a lot of Demon-only features, including line lock, a quick cooldown mode for the supercharged engine, and data recording. And of course there are pages to show a digital time slip with acceleration and braking figures, a g-load plot, and lots of gauges to track temps and levels. The engine output is shown in the video on a special Dyno page. It tracks horsepower and torque over time on the upper graph, and engine rpm and shift points on the lower graph. And we think it's still hiding something. This content is hosted by a third party. To view it, please update your privacy preferences. Manage Settings. Any good drag car has a line lock, allowing the driver to lock the front brakes and leave the rears free to do a nice tire-warming (or tire-shredding, depending on length) burnout. Ford has it on the Mustang, Chevy puts it on the ZL1, and now Dodge is adding it to the Demon. It should help get the giant Nitto tires up to temp for a drag run. And once the tires are warm, there's launch control, just like on the SRT Hellcat, with selectable rpm to dial things in for the conditions. The Demon also has a shift light in the cluster, and the driver can set a shift point individually for each gear. After each drag run, you can activate Quick Cooldown, which Dodge says uses the first production application of After-Run Chiller – it runs the cooling fan and intercooler coolant pump with the engine off until the coolant reaches its target temp. It's shown in one of the slides above. The checklist on the left side of that page suggests it requires a set of conditions be met to work: engine off, hood open, and sufficient battery level. This further reinforces our theory that the supercharger is going to make big boost, beyond the Hellcat's 11.6 psi. And while you're waiting for the supercharger to cool off for another run, you can review the performance data the car records.

Dodge Demon makes so much torque, it needs stronger driveline parts

Torque is a lovely thing, a sweet and wonderful force that twists and pulls and can help propel a two-ton metal box forward at comical speeds. Torque is also fickle and will bend and break those same metal parts without a second thought, which is why the new Dodge Demon is compensating for its increased torque with some new re-engineered and reinforced parts. And there's software intended to combat wheel hop, which one of the most dramatic ways torque can break stuff. Week 8's video, "Race-hardened Parts," gives a hint towards what all these new parts can do. While we still don't know how much torque the Demon will throw out, we do know it's enough to warrant an upgraded prop shaft, half shafts, and a differential housing. The Challenger Hellcat, which is the basis for the Demon, makes 650 pound-feet of torque already. The new parts will go a long way toward making sure the work from the Demon's engine is properly translated into motion by those Nitto drag radials. The new prop shaft uses high-strength steel, heat-treated stub-shafts, and increases the tube thickness by 20 percent for a 15 percent increase in torque capacity. Additionally, Dodge says the upgraded differential housing allows for a 30 percent increase in torque capacity by using heat-treated A383 aluminum alloy and a higher strength shot-peened gear set. The 41-spline half shafts that deliver 20 percent increased torque capacity through the use of high-strength low alloy steel and 8-ball joints. In addition to the hardware, the Launch Assist software has been tuned to help alleviate wheel hop. Dodge says the Demon is the first factory production car that uses wheel speed sensors to detect hop and momentarily cut torque to compensate. This means a driver can keep their foot planted on the floor while the computer sorts out the traction. Previously, the best solution was to back off the throttle to manually cut the load. Finally, the Dodge Demon will offer a four-point harness mounting bar as an optional accessory. The part will be supplied by Speedlogix and fits in place of the deleted rear seat. Customers can install the bar without having to hack apart their cars to find a proper mounting point. Look for more teasers and info on ifyouknowyouknow.com in the lead-up to the Demon's debut at the 2017 New York Auto Show. Related Video: Image Credit: FCA Dodge Performance dodge demon dodge hellcat

Consumer Reports says these are the worst new cars of 2014

Consumer Reports has announced its annual list of worst vehicles, a cringe-inducing contrast to its list of top vehicles. Ignominiously leading the way in 2014 is Chrysler, which has a staggering seven models listed.
Jeep nearly sweeps the small SUV segment by itself, with its Compass, Patriot and 2.4-liter version of the new Cherokee, while the only midsize sedans listed by CR were the Chrysler 200 and Dodge Avenger. The new Dodge Dart and the Dodge Journey round out CR's condemnation of Chrysler.
Ford is taking heat as well, with the Taurus, Edge and their counterparts from Lincoln all listed as the worst vehicles in their respective segments. Toyota doesn't fare much better, with its Lexus IS, Scion iQ and tC also making the list.