Mopar 1972 Dodge Dart Swinger on 2040-cars

Auto blog

Dodge engineers trying to shoehorn Pentastar into Dart?

The fact that the Dart's launch has been a pretty dismal affair isn't what we'd call secret. Judging by its mounting inventories and poor critical reception, Dodge's successor to its unloved Caliber has struggled since it hit the market. And while both of those are difficult problems to address, at least their cause is well known - the powertrain.
Even Fiat-Chrysler CEO Sergio Marchionne has acknowledged that the powertrain options in the Dart are substandard, admitting at January's Detroit Auto Show that the powertrains are "less than ideal." Leading with the 1.4-liter turbocharged four-cylinder found in the Fiat 500 Abarth left a bad taste in the mouths of consumers thanks to the laggy engine and dead throttle response (to say nothing of the manual and dual-clutch gearboxes that needed more refinement). The addition of the 184-horsepower 2.4-liter Tigershark in the Dart GT has helped matters some, but apparently Auburn Hills doesn't think it's quite enough.
If rumors are to be believed - get that salt ready - a possible solution may be in the works. A report from Allpar is claiming that Dodge is considering fitting a Pentastar V6 into the Dart's engine bay. As the Mopar-obsessed website points out, the critically acclaimed Pentastar is available in three different sizes - 3.0 liters, 3.2 liters and the original 3.6 liters. We don't get the 3.0 here in the US, but the 3.2 can be found in the new Jeep Cherokee and the 3.6 has been seemingly fitted to every model Chrysler can shoehorn it into.

2016 Dodge Viper ACR First Drive [w/video]

The Dodge Viper is not a comfortable car. Livable, yes. The interior is covered in fine materials. But you still climb over a hot door sill to enter the tiny cabin. And the frequency range of the engine's noises seem specifically designed to cause headaches. What happens, then, if you remove all pretense of civility from a Viper and add equipment solely aimed at improving lap times? You would have the 2016 Dodge Viper ACR. In terms of achieving its purpose, this car is a absolute success. In many ways it's also the most honest Viper of the current generation. Prices start at $121,990 (including $2,100 gas-guzzler tax and $1,995 destination), or $32,900 more than the least expensive Viper. In ACR trim, the Viper loses the under-carpet padding, 9 of 12 speakers plus amplifier, carpet and trim from the cargo area, and sound deadening in front of the rear wheel wells. The parts of the interior still covered add healthy amounts of Alcantara or optional carbon fiber. That weight loss is compensated by the addition of go-fast bits like the giant rear wing (or the larger "x-wing" on the Extreme Aero Package), 10-way adjustable Bilstein Motorsports shocks, Brembo carbon-ceramic brakes, a rear diffuser, and a front splitter. Total claimed curb weight is 3,392 pounds in Aero trim (standard ACR trim is 18 pounds lighter), which is within a few stone of the rest of the Viper lineup. The diffuser strakes and leading edge of the splitter are removable, made to be replaced after rubbing on track tarmac and make street driving slightly more practical. Not that you'd want to drive the ACR on the street, with the lack of noise insulation and spring rates twice as stiff as the Viper TA, but it is street-legal. Dodge claims the DOT-approved Kumho Ecsta V720 tires on the ACR allow faster lap times than some race compound tires. Our test was limited to on-track shenanigans at Virginia International Raceway. Which is fitting because we wouldn't have anything good to say about driving the car on the street. The ACR is, essentially, a race car sold in the showroom, although with the Viper's 1 of 1 customization program, your custom build can include as many creature comforts as you like. Lined up in pit lane at VIR, the Viper ACRs for our evaluation blur the air with heat shimmer. All of the test cars have air conditioning, but that shuts off at full throttle with a six-second reset.

Mopar unveils Dodge Challenger Drag Pak [w/video]

Dodge is going drag racing, and it's doing it with an all-new version of the Challenger for NHRA's Sportsman class. FCA's Mopar parts and performance arm announced the new Challenger Drag Pak Friday, showing off a version with a 354-cubic-inch (that's a 5.8-liter, by the way), supercharged V8 and a 426-ci (7.0-liter), naturally aspirated V8 – both Hemis, of course – that can get the big coupes through the quarter-mile in "the eight-second range." While the two engines deliver similar performance, at their base, they're quite a bit different. The supercharged model uses a cast-iron block, while the 426 has aluminum for both the block and head. That said, both models get customized engine calibrations, and are mated to unique, race-spec automatic transmissions. But drag racing is about far more than just outright power. Mopar significantly updated the four-link rear suspension, adding a four-inch rear axle from Strange Engineering, along with an aluminum, nine-inch third member, while the rear-axle housing has been strengthened in general. Both the rear shocks and front struts can be adjusted for rebound and compression, too. Lightweight 15-inch wheels, meanwhile, are shod in super-sticky Hoosier drag radials, with nine inches of tread in back and 4.5 inches in front. The new Challenger Drag Pak should run the quarter-mile in "the eight-second range." In the cabin, there's an NHRA-spec roll cage, a Racepak gauge cluster, and a handsome pair of Sparco racing seats. Outside, supercharged models get blue decals, while naturally aspirated varieties get black stickers, although there's more to the new Challenger dragster's exterior than just its decals. Mopar tweaked the big-scoop hood, promising it's easier to get up to check on the engine, and the designers also added trailer tie-down straps in both the front and rear. While the dragster was the big news today, Mopar officials also announced the two enhanced Scat Pack kits for both the Dodge Charger and Challenger R/T. The 5.7-liter Hemi models gain an extra 56 horsepower and 30 pound-feet of torque in the Scat Pack 2 thanks to a new cam, valve springs, pushrods, and gaskets. The Scat Pack 3, meanwhile, adds 75 hp and 44 lb-ft, on top of the gains from the lower packages. That should be perfect for drivers who wish to snort in the face of their SRT 392-driving friends. The third stage adds a ported cylinder heads, as well as high-flow manifolds and catalysts.