1994 Dodge Dakota Slt Mark Iii Conversion 64,994 Original Miles on 2040-cars

Auto blog

2014 Challenger R/T Shaker, Mopar '14 Challenger bring back iconic hood

Enamored of the Dodge Challenger but wish you could get one with a shaker hood? We've got good news, because Dodge and Mopar have teamed up to bring it back.
The 2014 Dodge Challenger R/T Shaker packs the same 5.7-liter Hemi V8 as the standard Challenger R/T, but upgrades the business end with a through-the-hood exposed cold-air intake system. The retro hood scoop protrudes from the center of the hood in satin black (matching the decklid spoiler) to feed the Hemi and shakes with the engine just like the original from 1970. The Shaker model also comes with a Super Track Pak that adds a new steering rack, brake linings, shocks and 20-inch Goodyear Eagle F1 Super Car rubber. You can also shut off the stability management system completely in this car. A series of interior and exterior trim enhancements round out the look. The whole package adds $2,500 to the price of a Challenger R/T Classic for an all-in MSRP of $36,995.
In case that's not enough, Dodge is also offering a limited-edition Mopar Challenger that follows the 2010 Mopar Challenger, 2011 Mopar Charger, 2012 Mopar 300 and 2013 Mopar Dart. Limited to just 100 examples, the 2014 Mopar Challenger gets the same Shaker hood intake, unique graphics and wheels, an enhanced interior and a long list of optional extras from the Mopar parts catalog. Dodge isn't saying just yet how much the Mopar Challenger will cost, but you can bet it will command a considerable premium for the exclusivity alone.

Dodge Viper recall requires small-handed mechanics

It has been over a year since Chrysler first announced its recall of 3,660 2003-2004 Dodge Vipers because the airbag could suddenly deploy. The repairs are finally beginning, and it appears to be a nightmare for mechanics.
According to the automaker's filing with the National Highway Traffic Safety Administration, the airbag control module can fail, which causes the bag or the seatbelt pre-tensioner to deploy without warning. It took over a year to design the new parts, according to The New York Times. However, Chrysler finally has a new "jumper harness with an in-line diode filter circuit" ready to fix the problem.
The dilemma now moves to the mechanics who have to actually install the part. A 47-step guide from Chrysler explains that the procedure should take about two hours. It's not an easy job, though. Most of the dashboard has to be taken apart, and the instructions include this helpful bit of advice: "Installing the jumper harness and filter box into position is not an easy task. Patience, perseverance, and small hands are required." We wish the best of luck to them. The fix comes just in time for the Vipers to enjoy the summer sun.

Chrysler says its 8-speed transmissions will save 700 million gallons

Chrysler Group's TorqueFlite eight-speed transmission could be earning some serious green bragging rights if the company's projections are correct. The recently widely proliferated automatic gearbox, which is now in more than a million vehicles around the world, is poised to save drivers an estimated 700+ million gallons of fuel over the vehicles' lifetimes (an expected cost savings of $2.5 billion). In addition, Chrysler expects a reduction in CO2 emissions by more than six million metric tons. According to Chrysler, and depending on the vehicle, the TorqueFlite can improve fuel economy. The TorqueFlite autobox features particularly close ratios from fifth to eighth gear (see the press release below for the specific numbers), and uses low-viscosity fluid that doesn't need to be replaced. Transmission software adapts to the driving situation to optimize efficiency based on driver behavior, temperature, grade, stability control, and longitudinal and lateral acceleration. The TorqueFlite is capable of handling a variety of duties. As evidenced by the wide range of vehicles Chrysler Group has seen fit to equip with the eight-speed transmission, the TorqueFlite is capable of handling a variety of duties. Since its 2012 introduction, the TorqueFlite has gone from performing cog-swapping duties in Dodge Charger and Chrysler 300 models equipped with the 3.6-liter Pentastar V6 to changing gears in vehicles such as the Pentastar- and Hemi-powered Dodge Durango, Jeep Grand Cherokee and even the Ram 1500 EcoDiesel. For the 2015 model year, the eight-speed is finding its way into even more vehicles with the addition of a third version. In addition to the American-made TorqueFlite 845RE and 8HP70, the new 8HP90 will be manufactured in Saarbrucken, Germany. The 8HP90 is designed for higher torque loads, making it ideal for high-performance vehicles like the 2015 Dodge Challenger SRT Hellcat. The already-in-use 8HP70 will expand its duties to be used in 2015 Hemi models such as the Dodge Charger, Challenger, and Challenger SRT8. You can see the list of those benchmarks in Chrysler's press release below.