1969 Dodge Superbee One Family Owned # Match Survivor on 2040-cars

Auto blog

Dodge Challenger SRT Hellcat vs. Chevrolet Camaro ZL1 in latest Head 2 Head

"Olympian" is one of the terms we use to signify the greatest height, the seat of the gods. Yet Mt. Olympus is the second-highest peak in the Balkans ranges, overshadowed by the crest at Musala in Bulgaria's Rila mountains. Both great heights, but one is a little higher. That's how we get the Olympian Chevy Camaro ZL1 pitched at the Musalic Dodge Challenger SRT Hellcat in Motor Trend's latest episode of Head 2 Head. The side-by-side spec sheet is filled with farcical numbers. For the ZL1, that's a 6.2-liter V8 with 580 horsepower, 556 pound-feet of torque, a 4,051-pound curb weight, 0-to-60 miles per hour in 3.9 seconds, a quarter-mile time of 12.2 seconds and a base price of just $57,800. Opposing that, the Hellcat wrings out its 6.2-liter V8 for 707 hp, 650 lb-ft of torque, weighs 4,449 pounds, does the quarter in 11.7 seconds and has a base price of just $60,990. Except in the case of the Hellcat, when Motor Trend put it on the dyno the machine spit out a reading of 672 hp and 606 lb-ft at the wheels. If there's a 10-percent driveline loss through those beefed-up internals and heavy-duty eight-speed transmission, that means the Hellcat is actually rated at about 750 horsepower and 700 lb-ft. But once they get put on a closed-off strip of coast road in Northern California, there are only a few strands of hair between their respective performances. That's not the case for they sensations provide; host Jonny Lieberman calls one of them, "One of the most incredible cars ever made," and says, "It changes everything." Watch the video above to see who got the verdict and how. Related Video:

2016 Dodge Charger Pursuit Vehicle Gets Uconnect 12.1 | Autoblog Minute

Dodge introduces new tech into its 2016 pursuit vehicles that even Jake and Elwood couldn?t outrun. Autoblog's Adam Morath reports on this edition of Autoblog Minute.

Mopar unveils Dodge Challenger Drag Pak [w/video]

Dodge is going drag racing, and it's doing it with an all-new version of the Challenger for NHRA's Sportsman class. FCA's Mopar parts and performance arm announced the new Challenger Drag Pak Friday, showing off a version with a 354-cubic-inch (that's a 5.8-liter, by the way), supercharged V8 and a 426-ci (7.0-liter), naturally aspirated V8 – both Hemis, of course – that can get the big coupes through the quarter-mile in "the eight-second range." While the two engines deliver similar performance, at their base, they're quite a bit different. The supercharged model uses a cast-iron block, while the 426 has aluminum for both the block and head. That said, both models get customized engine calibrations, and are mated to unique, race-spec automatic transmissions. But drag racing is about far more than just outright power. Mopar significantly updated the four-link rear suspension, adding a four-inch rear axle from Strange Engineering, along with an aluminum, nine-inch third member, while the rear-axle housing has been strengthened in general. Both the rear shocks and front struts can be adjusted for rebound and compression, too. Lightweight 15-inch wheels, meanwhile, are shod in super-sticky Hoosier drag radials, with nine inches of tread in back and 4.5 inches in front. The new Challenger Drag Pak should run the quarter-mile in "the eight-second range." In the cabin, there's an NHRA-spec roll cage, a Racepak gauge cluster, and a handsome pair of Sparco racing seats. Outside, supercharged models get blue decals, while naturally aspirated varieties get black stickers, although there's more to the new Challenger dragster's exterior than just its decals. Mopar tweaked the big-scoop hood, promising it's easier to get up to check on the engine, and the designers also added trailer tie-down straps in both the front and rear. While the dragster was the big news today, Mopar officials also announced the two enhanced Scat Pack kits for both the Dodge Charger and Challenger R/T. The 5.7-liter Hemi models gain an extra 56 horsepower and 30 pound-feet of torque in the Scat Pack 2 thanks to a new cam, valve springs, pushrods, and gaskets. The Scat Pack 3, meanwhile, adds 75 hp and 44 lb-ft, on top of the gains from the lower packages. That should be perfect for drivers who wish to snort in the face of their SRT 392-driving friends. The third stage adds a ported cylinder heads, as well as high-flow manifolds and catalysts.