1965 Dodge Cornett on 2040-cars

Auto blog

Brand new cars are being sold with defective Takata airbags

If you just bought a 2016 Audi TT, 2017 Audi R8, 2016–17 Mitsubishi i-MiEV, or 2016 Volkswagen CC, we have some unsettling news for you. A report provided to a US Senate committee that oversees the US National Highway Traffic Safety Administration (NHTSA) and reported on by Automotive News claims these vehicles were sold with defective Takata airbags. And it gets worse. Toyota and FCA are called out in the report for continuing to build vehicles that will need to be recalled down the line for the same issue. That's not all. The report also states that of the airbags that have been replaced already in the Takata recall campaign, 2.1 million will need to eventually be replaced again. They don't have the drying agent that prevents the degradation of the ammonium nitrate, which can lead to explosions that can destroy the airbag housing and propel metal fragments at occupants. So these airbags are out there already. We're not done yet. There's also a stockpile of about 580,000 airbags waiting to be installed in cars coming in to have their defective airbags replaced. These 580k airbags also don't have the drying agent. They'll need to be replaced down the road, too. A new vehicle with a defective Takata airbag should be safe to drive, but that margin of safety decreases with time. If all this has you spinning around in a frustrated, agitated mess, there's a silver lining that is better than it sounds. So take a breath, run your fingers through your hair, and read on. Our best evidence right now demonstrates that defective Takata airbags – those without the drying agent that prevents humidity from degrading the ammonium nitrate propellant – aren't dangerous yet. It takes a long period of time combined with high humidity for them to reach the point where they can rupture their housing and cause serious injury. It's a matter of years, not days. So a new vehicle with a defective Takata airbag should be safe to drive, but that margin of safety decreases with time – and six years seems to be about as early as the degradation happens in the worst possible scenario. All this is small comfort for the millions of people who just realized their brand-new car has a time bomb installed in the wheel or dashboard, or the owners who waited patiently to have their airbags replaced only to discover that the new airbag is probably defective in the same way (although newer and safer!) as the old one.

Dodge Viper to out-Hell the Hellcat with supercharged V10?

The Viper wouldn't be the Viper if it wasn't the most powerful model under the Chrysler umbrella. But with the arrival of the Hellcat engine in the Dodge Charger and Challenger, the Viper has fallen behind in the bragging rights department: where the new supercharged V8 produces 707 horsepower and 650 pound-feet of torque, the naturally aspirated V10 offers "only" 640 hp and 600 lb-ft - gargantuan output figures by almost any other standard, but crucially behind on the SRT power scale. Conner Avenue is going to have to do something about that.
Although the Hellcat's engine reportedly won't fit under the Viper's hood, SRT is now rumored to have another trick up its sleeve: supercharge the existing V10. According to the Pentastar performance enthusiasts at allpar.com, Chrysler has already taken delivery of the first such prototype engines so that it can begin the process of fitting it into an upgraded Viper.
The spooled ten-pot is tipped to produce around 800 hp and 650 lb-ft of torque. More than that and the Viper's drivetrain, chassis and bodywork would have to be substantially reworked. Though beefier transmissions are available, fitting them would reportedly set off a domino-game of changes required to handle the added torque. Which may be something Chrysler would be prepared to do for the next-generation model, but in the meantime, 800 hp could prove enough to put the Viper back atop the Mopar performance ladder where it belongs, and give it an edge against the new Corvette Z06 to rekindle sales.

Chrysler investing $20M in Toledo plant to support 9-speed auto production

In 2011, Chrysler announced a $72-million investment in its Toledo Machining Plant to modernize production of the eight- and nine-speed torque-converters for automatic transmissions made there. That upgrade work won't be finished until Q3 of this year, but Chrysler has already announced a further $19.6-million investment to increase production capacity for the nine-speeders.
The extra units will be necessary because the nine-speed transmission they'll be mated to is going into three popular models: it will debut on the 2014 Jeep Cherokee, then go into the Chrysler 200 and Dodge Dart. The company predicted that this year alone it would sell 200,000 units equipped with the nine-speed tranny, and it is spending some $374 million in addition to the investment in Toledo to upgrade production capacity for it.
The work attached to this new investment won't begin until Q3 of 2014, and it will be finished by the end of that year. There's a press release below with all the details.