2012 Dodge Charger Sxt Rallye Package 1-owner 20-inch Wheels Heated-seats Mint! on 2040-cars

Auto blog

Stormtrooper Dodge Charger Episode VII: The Charger Awakens

We spent a day with a Dodge Charger that looks like a Stormtrooper helmet and made a few videos. This one features the Hemi V8 starting up. Read about the car and watch the rest of the videos here.

Dodge Charger Hellcat makes 1,032 hp with Hennessey help

Sometimes you just want four doors. Earlier this week we brought you Hennessey's riff on the Dodge Challenger Hellcat. Now comes the Charger. Much like its two-door sibling, the Charger gets boosted to as much as 1,032 hp and 987 lb-ft of torque (at the crank) thanks to the addition of a twin-turbocharging setup that works with the factory supercharger. The turbo headers and downpipes are stainless steel, and there is a high-flow air-to-water intercooler and dual-turbo waste gates. Hennessey also beefs up the fuel injectors, fuel pump, and the rest of the fuel system. The engine management system and chassis are recalibrated to accommodate all of this. You also get numbered plaques signed by John Hennessey, the boss of the Texas tuning outfit, and the technician who does your build. Hennessey's additions result in zero-to-60 mph sprints in 2.7 seconds, and the big sedan can run the quarter mile in 9.9 seconds at 142 mph. Like the Challenger, the Charger has the same disclaimer: the lofty horsepower figure comes from an engine dyno, and it will be a 15-to 20-percent lower at the rear wheels. Related Video: Image Credit: Hennessey Performance Dodge Performance Sedan Hennessey dodge charger hellcat

Mopar unveils Dodge Challenger Drag Pak [w/video]

Dodge is going drag racing, and it's doing it with an all-new version of the Challenger for NHRA's Sportsman class. FCA's Mopar parts and performance arm announced the new Challenger Drag Pak Friday, showing off a version with a 354-cubic-inch (that's a 5.8-liter, by the way), supercharged V8 and a 426-ci (7.0-liter), naturally aspirated V8 – both Hemis, of course – that can get the big coupes through the quarter-mile in "the eight-second range." While the two engines deliver similar performance, at their base, they're quite a bit different. The supercharged model uses a cast-iron block, while the 426 has aluminum for both the block and head. That said, both models get customized engine calibrations, and are mated to unique, race-spec automatic transmissions. But drag racing is about far more than just outright power. Mopar significantly updated the four-link rear suspension, adding a four-inch rear axle from Strange Engineering, along with an aluminum, nine-inch third member, while the rear-axle housing has been strengthened in general. Both the rear shocks and front struts can be adjusted for rebound and compression, too. Lightweight 15-inch wheels, meanwhile, are shod in super-sticky Hoosier drag radials, with nine inches of tread in back and 4.5 inches in front. The new Challenger Drag Pak should run the quarter-mile in "the eight-second range." In the cabin, there's an NHRA-spec roll cage, a Racepak gauge cluster, and a handsome pair of Sparco racing seats. Outside, supercharged models get blue decals, while naturally aspirated varieties get black stickers, although there's more to the new Challenger dragster's exterior than just its decals. Mopar tweaked the big-scoop hood, promising it's easier to get up to check on the engine, and the designers also added trailer tie-down straps in both the front and rear. While the dragster was the big news today, Mopar officials also announced the two enhanced Scat Pack kits for both the Dodge Charger and Challenger R/T. The 5.7-liter Hemi models gain an extra 56 horsepower and 30 pound-feet of torque in the Scat Pack 2 thanks to a new cam, valve springs, pushrods, and gaskets. The Scat Pack 3, meanwhile, adds 75 hp and 44 lb-ft, on top of the gains from the lower packages. That should be perfect for drivers who wish to snort in the face of their SRT 392-driving friends. The third stage adds a ported cylinder heads, as well as high-flow manifolds and catalysts.