2008 Dodge Challenger Srt8 Coupe 2-door 6.1l on 2040-cars

Auto blog

Dodge Hornet supposedly snapped inside Alfa Romeo Tonale factory

It appears that someone in Stellantis' Pomigliano d’Arco Assembly Plant in Italy couldn't keep their cellphone to themselves. Video uploaded to the Alfa Romeo Club Italia Facebook page, then quickly removed, purports to show Dodge's brand-engineered version of the Alfa Romeo Tonale in the same factory where the Alfa will be built. The Dodge is expected to be called the Hornet, and there are a few differences between it and and Alfa Romeo, which is understandable. But if the screenshots on Twitter are accurate, then the Dodge looks a lot closer to the Alfa Romeo than perhaps anyone expected. The front fascia and hood fall in line with Dodge's design language. The Alfa grille is replaced by a narrow, stepped upper grille, and the hood is one of the vented units similar to those available for Dodge's R/T performance trims. And as Mopar Insiders noticed, the silhouette of this car's front end matches a vehicle silhouette Dodge showed during Stellantis' 2021 EV Day.   Inside, the Italian brand's crest in the steering wheel center cap is replaced by Dodge's twin slashes, and the steering wheel has been stripped of the large, curved paddle shifters the Tonale showed on its debut. There's still a start/stop button on the steering wheel, but where the Tonale has a driving mode dial on its dash, this supposed Hornet has another start/stop button. Dodge's push-to-start buttons are usually on the instrument panel, so our guess is that the wheel is a holdover for testing. On the center tunnel, the parking alert buttons and Italian Tricolore flag on the Alfa Romeo are replaced by three different buttons.   We've known Dodge has two electrified vehicles on the way, and the Hornet name has been low-key buzzing for two years. Fiat Chrysler applied to trademark the name in the U.S. in March 2020; at the time, it was thought a vehicle with that name could replace the Journey. In 2021, a July rumor out of Italy was the first whisper of the Hornet name being attached to the Alfa Romeo Tonale. In August, when Stellantis CEO Carlos Tavares said Dodge would get a PHEV in 2024, watchers pegged that model as the Hornet. That hybrid powertrain would show a year after the vehicle's launch, the Hornet anticipated as a 2023 model with the Tonale's turbocharged 2.0-liter four-cylinder. That engine could get the same 256 horsepower and 295 pound-feet of torque as the Tonale, or be boosted to satisfy Dodge's performance credentials.

Certain Chrysler owners eligible for buyback program

Certain car owners whose Chrysler vehicles contain dangerous defects will soon have a way to get rid of their lemons without losing money. As part of an agreement with federal regulators, Fiat Chrysler Automobiles has agreed to buy back more than 500,000 vehicles susceptible to veering out of control without warning at above market-value prices. The deal mainly covers certain models of RAM trucks, the Dodge Dakota pickup and Dodge Durango SUV. Further, owners of more than 1.5 million Jeep Liberty and Grand Cherokees at heightened risk for lethal fires are eligible to trade in their vehicles at above market value or, alternately, get a gift certificate if they prefer to have repairs made. Chrysler has "a heavy responsibility to make sure the products they make are safe for the traveling public," said Mark Rosekind, administrator of the National Highway Traffic Safety Administration. "... Here, we are sending an unambiguous signal to industry that if you skirt the laws or violate the law, or don't live up to the responsibility that consumers expect, we are going to penalize you." The buy-back and trade-in options for motorists come as part of an unprecedented penalty NHTSA slapped against Chrysler for violating federal motor-vehicle safety laws. Chrysler will pay a $105 million fine, the highest ever levied by the regulatory agency. In addition to the buy-backs, Chrysler also agreed to an independent monitor for three years. Investigators had outlined problems in the company's conduct in 23 recalls that affected more than 11 million defect vehicles. As part of a consent-order agreement, Chrysler acknowledged it did not notify vehicle owners of recalls in an effective manner and did not notify NHTSA of safety problems. Though those recalls affected millions of drivers, the buy-back and trade-in options are only for a small portion of the vehicles involved. Because Chrysler struggled to fix the problem and no repair was apparent, Rosekind said the buy-backs are reserved "for customers who didn't have a remedy." Buy-backs are for trucks and SUVs affected by three recalls that occurred in 2013 (recalls 13V-038, 13V-527 and 13V-529), that addressed a rear-axle pinion nut that could come loose and cause a loss of vehicle control. Those recalls covered 579,228 vehicles, including 2009-2012 Ram 1500, 2500, 3500, 4500 and 5500 trucks, 2009-2012 Dodge Dakotas, 2009 Chrysler Aspen and the 2009 Dodge Durango.

Mopar unveils Dodge Challenger Drag Pak [w/video]

Dodge is going drag racing, and it's doing it with an all-new version of the Challenger for NHRA's Sportsman class. FCA's Mopar parts and performance arm announced the new Challenger Drag Pak Friday, showing off a version with a 354-cubic-inch (that's a 5.8-liter, by the way), supercharged V8 and a 426-ci (7.0-liter), naturally aspirated V8 – both Hemis, of course – that can get the big coupes through the quarter-mile in "the eight-second range." While the two engines deliver similar performance, at their base, they're quite a bit different. The supercharged model uses a cast-iron block, while the 426 has aluminum for both the block and head. That said, both models get customized engine calibrations, and are mated to unique, race-spec automatic transmissions. But drag racing is about far more than just outright power. Mopar significantly updated the four-link rear suspension, adding a four-inch rear axle from Strange Engineering, along with an aluminum, nine-inch third member, while the rear-axle housing has been strengthened in general. Both the rear shocks and front struts can be adjusted for rebound and compression, too. Lightweight 15-inch wheels, meanwhile, are shod in super-sticky Hoosier drag radials, with nine inches of tread in back and 4.5 inches in front. The new Challenger Drag Pak should run the quarter-mile in "the eight-second range." In the cabin, there's an NHRA-spec roll cage, a Racepak gauge cluster, and a handsome pair of Sparco racing seats. Outside, supercharged models get blue decals, while naturally aspirated varieties get black stickers, although there's more to the new Challenger dragster's exterior than just its decals. Mopar tweaked the big-scoop hood, promising it's easier to get up to check on the engine, and the designers also added trailer tie-down straps in both the front and rear. While the dragster was the big news today, Mopar officials also announced the two enhanced Scat Pack kits for both the Dodge Charger and Challenger R/T. The 5.7-liter Hemi models gain an extra 56 horsepower and 30 pound-feet of torque in the Scat Pack 2 thanks to a new cam, valve springs, pushrods, and gaskets. The Scat Pack 3, meanwhile, adds 75 hp and 44 lb-ft, on top of the gains from the lower packages. That should be perfect for drivers who wish to snort in the face of their SRT 392-driving friends. The third stage adds a ported cylinder heads, as well as high-flow manifolds and catalysts.