1971 Dodge Challenger on 2040-cars

Auto blog

Dodge Journey and Fiat Freemont engine-cover recall affects 350k CUVs

FCA is recalling 349,731 examples of the 2011-2015 Dodge Journey and Fiat Freemont worldwide to better secure their engine covers. Of these affected vehicles, there are 144,416 in the US, 43,679 in Canada, 46,231 in Mexico, and 115,405 elsewhere. About 10 percent of them are also still at dealers, according to the automaker. Only models with the 2.4-liter four-cylinder engine are affected by this campaign. According to the company, the engine covers on these vehicles can be dislodged, and this can pose a fire risk if the loose part comes in contact with hot exhaust components. Warning signs of this happening include a noise under the hood, burning smell or a light on the instrument panel. The problem was discovered after three incidents on rough roads in Chile, and there was one minor injury there. According to FCA US spokesperson Eric Mayne to Autoblog, there have been eight occurrences of this issue reported in the US, but these were all related to "heat damage." There have been no reported injuries here. To fix the problem, dealers will install new engine-cover retainers on the affected models. These repairs will begin in August. As always for recall repairs, owners won't be charged. Statement: Engine Cover July 22, 2015 , Auburn Hills, Mich. - FCA US LLC is voluntarily recalling an estimated 144,416 crossover utility vehicles (CUVs) in the U.S. to better secure their engine covers. Engine covers in certain vehicles may become dislodged. If they come in contact with exhaust components, it may pose a fire risk. This condition was discovered during an FCA US investigation of three incidents in Chile. In each case, the vehicle had been driven extensively on unpaved or uneven surfaces. The Company is aware of a single related injury, described as minor. Affected are 2011-2015 Dodge Journey and Fiat Freemont CUVs equipped with 2.4-liter, four-cylinder engines. FCA US will install upgraded engine-cover retainers in these vehicles. The remedy will be available when customer notification begins next month; service will be performed free of charge. Vehicles equipped with six-cylinder engines are not affected. Additional Journey and Freemont populations also are subject to this campaign. They comprise an estimated 43,679 vehicles in Canada; 46,231 in Mexico; and 115,405 outside the NAFTA region. Of the 349,731 total vehicles subject to this campaign, approximately 10 percent remain in dealer hands.

Dodge Demon makes so much torque, it needs stronger driveline parts

Torque is a lovely thing, a sweet and wonderful force that twists and pulls and can help propel a two-ton metal box forward at comical speeds. Torque is also fickle and will bend and break those same metal parts without a second thought, which is why the new Dodge Demon is compensating for its increased torque with some new re-engineered and reinforced parts. And there's software intended to combat wheel hop, which one of the most dramatic ways torque can break stuff. Week 8's video, "Race-hardened Parts," gives a hint towards what all these new parts can do. While we still don't know how much torque the Demon will throw out, we do know it's enough to warrant an upgraded prop shaft, half shafts, and a differential housing. The Challenger Hellcat, which is the basis for the Demon, makes 650 pound-feet of torque already. The new parts will go a long way toward making sure the work from the Demon's engine is properly translated into motion by those Nitto drag radials. The new prop shaft uses high-strength steel, heat-treated stub-shafts, and increases the tube thickness by 20 percent for a 15 percent increase in torque capacity. Additionally, Dodge says the upgraded differential housing allows for a 30 percent increase in torque capacity by using heat-treated A383 aluminum alloy and a higher strength shot-peened gear set. The 41-spline half shafts that deliver 20 percent increased torque capacity through the use of high-strength low alloy steel and 8-ball joints. In addition to the hardware, the Launch Assist software has been tuned to help alleviate wheel hop. Dodge says the Demon is the first factory production car that uses wheel speed sensors to detect hop and momentarily cut torque to compensate. This means a driver can keep their foot planted on the floor while the computer sorts out the traction. Previously, the best solution was to back off the throttle to manually cut the load. Finally, the Dodge Demon will offer a four-point harness mounting bar as an optional accessory. The part will be supplied by Speedlogix and fits in place of the deleted rear seat. Customers can install the bar without having to hack apart their cars to find a proper mounting point. Look for more teasers and info on ifyouknowyouknow.com in the lead-up to the Demon's debut at the 2017 New York Auto Show. Related Video: Image Credit: FCA Dodge Performance dodge demon dodge hellcat

Fiat Chrysler taps Amazon, Shell execs to fill roles

MILAN — Fiat Chrysler Automobiles is tapping executives from Amazon and Shell Oil Company with previous automotive industry experience to fill its ranks. CEO Mike Manley said in a letter to employees Thursday that Mark Stewart would join FCA as chief operating officer of North America from Amazon, "a company known for its culture of innovation, and obsession with delivering incredible value to customers." At Amazon, Stewart led teams focused on advanced robotics, artificial intelligence and automation methods. He previously was COO of ZF TRW automotive components supplier. Niel Golightly was named head of global communications. He was most recently Shell's vice president for external relations in North and South America, with a focus on reputation, brand and stakeholder engagement beyond communication strategies. He previously held roles at Ford Motor Company. Related Video: Image Credit: REUTERS/Rebecca Cook Hirings/Firings/Layoffs Alfa Romeo Chrysler Dodge Fiat Jeep RAM FCA Amazon shell Mike Manley