2008 Freightliner Sprinter 170" Hi Top One Owner Clean Carfax Turbo Diesel Dodge on 2040-cars

Auto blog

Common Dodge Ram 1500 vs. Chevrolet Silverado breakdowns

These two trucks are famous for their ability to get the job done. Still, even the toughest vehicle can have mechanical problems at some time. What if we match the Dodge Ram 1500 and Chevrolet Silverado head to head? Let's find out more about common repairs for each model. Also, learn some tricks to pay for car repairs. Clunky Steering Both Dodge and the Chevy owners sometimes notice bumping and clunking when steering. This might be more noticeable when driving over bumps. The cause is usually different in each truck though. In the Dodge Ram, clunky steering is more likely due to a defective lower ball joint. Replacement costs around $300 - $400, parts and labor. Clunky Chevy Silverado steering is probably a steering rack failure. This problem appears more often in trucks with over 90,000 miles. Silverado steering rack repair will run you up to $1,000 or more. Starting Woes For the Chevy Silverado with over 130,000 miles, you might notice trouble starting. This problem may appear occasionally at first, but it typically gets worse. Excluding a weak battery, the culprit is usually the starter. Replacement will cost you around $330 - $500. Of the total cost, $90 is for labor only. Now the Dodge Ram might make a ticking sound when starting, especially on models with over 94,500 miles. The noise often disappears after the engine warms up. These symptoms may indicate a broken exhaust manifold. Repair costs range from $800 - $900. Burning Oil & Gas Gauge On The Blink Sometimes, the Dodge Ram burns oil much faster than normal. In models with over 125,000 miles, this often points towards a leaky intake manifold gasket. A knocking sound may also appear with acceleration along with possible engine misfire. The cost to repair is around $200 - $300. The Chevy Silverado has its own surprises, especially when you've filled the gas tank but the gauge still reads low. Or the needle fluctuates widely from low to full while driving. In trucks with over 120,000 miles, it's likely due to a faulty fuel sensor. You might need a full fuel pump replacement, which can cost you up to $820, parts and labor. Water Inside And Poor Heat The Ram 1500 rear window has been known to leak. You might notice the back seat and floor wet after a rainstorm. This is more common in trucks with over 65,000 miles. Resealing the Ram 1500 rear window costs around $150 - $250.

Dodge Journey and Fiat Freemont engine-cover recall affects 350k CUVs

FCA is recalling 349,731 examples of the 2011-2015 Dodge Journey and Fiat Freemont worldwide to better secure their engine covers. Of these affected vehicles, there are 144,416 in the US, 43,679 in Canada, 46,231 in Mexico, and 115,405 elsewhere. About 10 percent of them are also still at dealers, according to the automaker. Only models with the 2.4-liter four-cylinder engine are affected by this campaign. According to the company, the engine covers on these vehicles can be dislodged, and this can pose a fire risk if the loose part comes in contact with hot exhaust components. Warning signs of this happening include a noise under the hood, burning smell or a light on the instrument panel. The problem was discovered after three incidents on rough roads in Chile, and there was one minor injury there. According to FCA US spokesperson Eric Mayne to Autoblog, there have been eight occurrences of this issue reported in the US, but these were all related to "heat damage." There have been no reported injuries here. To fix the problem, dealers will install new engine-cover retainers on the affected models. These repairs will begin in August. As always for recall repairs, owners won't be charged. Statement: Engine Cover July 22, 2015 , Auburn Hills, Mich. - FCA US LLC is voluntarily recalling an estimated 144,416 crossover utility vehicles (CUVs) in the U.S. to better secure their engine covers. Engine covers in certain vehicles may become dislodged. If they come in contact with exhaust components, it may pose a fire risk. This condition was discovered during an FCA US investigation of three incidents in Chile. In each case, the vehicle had been driven extensively on unpaved or uneven surfaces. The Company is aware of a single related injury, described as minor. Affected are 2011-2015 Dodge Journey and Fiat Freemont CUVs equipped with 2.4-liter, four-cylinder engines. FCA US will install upgraded engine-cover retainers in these vehicles. The remedy will be available when customer notification begins next month; service will be performed free of charge. Vehicles equipped with six-cylinder engines are not affected. Additional Journey and Freemont populations also are subject to this campaign. They comprise an estimated 43,679 vehicles in Canada; 46,231 in Mexico; and 115,405 outside the NAFTA region. Of the 349,731 total vehicles subject to this campaign, approximately 10 percent remain in dealer hands.

Dodge idles Viper production again at Conner Avenue

You've got to hand it to Dodge for having the gumption to put the original Viper into production in the first place. It was, after all, much more of an emotional decision than a practical one, and a move which saw the first production V10 engine placed in a road car - long before the advent of the Lamborghini Gallardo, Audi R8, Porsche Carrera GT or Lexus LFA, not to mention the other Ford, BMW and Volkswagen Group models that used such engines.
It's now been 22 years since the first Viper entered production and the Viper still rolls on several generations later, but we're sad to say that courageous decision has not always been met with overwhelming sales success. In fact parent Chrysler was forced to idle the Conner Avenue plant where the Viper is made back in April due to slow sales. And while production resumed again as planned on June 23, it apparently didn't do the trick.
As a result, Chrysler corporate communications chief Shawn Morgan revealed to Autoblog that the assembly line has been shut down again for another two weeks. The line was up and running for nearly two full work weeks from June 23 until the holiday weekend that started on Thursday, July 3. But instead of coming back online today as planned, it's been idled again for the weeks of July 7 and 14. That means it will be July 21, at the earliest, before the serpentine supercars start slithering down the assembly line at Conner Avenue again. Once it does, however, production is set to resume at the same pace it was before the shutdown.