Quad Cab Dually Cummins 5.9turbo Diesel Super Clean Florida Car Clean Carfax on 2040-cars

Auto blog

Dodge Demon makes so much torque, it needs stronger driveline parts

Torque is a lovely thing, a sweet and wonderful force that twists and pulls and can help propel a two-ton metal box forward at comical speeds. Torque is also fickle and will bend and break those same metal parts without a second thought, which is why the new Dodge Demon is compensating for its increased torque with some new re-engineered and reinforced parts. And there's software intended to combat wheel hop, which one of the most dramatic ways torque can break stuff. Week 8's video, "Race-hardened Parts," gives a hint towards what all these new parts can do. While we still don't know how much torque the Demon will throw out, we do know it's enough to warrant an upgraded prop shaft, half shafts, and a differential housing. The Challenger Hellcat, which is the basis for the Demon, makes 650 pound-feet of torque already. The new parts will go a long way toward making sure the work from the Demon's engine is properly translated into motion by those Nitto drag radials. The new prop shaft uses high-strength steel, heat-treated stub-shafts, and increases the tube thickness by 20 percent for a 15 percent increase in torque capacity. Additionally, Dodge says the upgraded differential housing allows for a 30 percent increase in torque capacity by using heat-treated A383 aluminum alloy and a higher strength shot-peened gear set. The 41-spline half shafts that deliver 20 percent increased torque capacity through the use of high-strength low alloy steel and 8-ball joints. In addition to the hardware, the Launch Assist software has been tuned to help alleviate wheel hop. Dodge says the Demon is the first factory production car that uses wheel speed sensors to detect hop and momentarily cut torque to compensate. This means a driver can keep their foot planted on the floor while the computer sorts out the traction. Previously, the best solution was to back off the throttle to manually cut the load. Finally, the Dodge Demon will offer a four-point harness mounting bar as an optional accessory. The part will be supplied by Speedlogix and fits in place of the deleted rear seat. Customers can install the bar without having to hack apart their cars to find a proper mounting point. Look for more teasers and info on ifyouknowyouknow.com in the lead-up to the Demon's debut at the 2017 New York Auto Show. Related Video: Image Credit: FCA Dodge Performance dodge demon dodge hellcat

Ram, Jeep redesigns on hold, Alfa Romeo models may come sooner

Last summer, FCA outlined an ambitious five-year plan that sketched out the company's product intentions for each of its brands through the end of 2018. However, even the best strategies sometimes need tweaking. According to Reuters after speaking with unnamed people at auto suppliers, FCA is now possibly delaying at least a dozen projects in North America for a variety of reasons. From vehicle to vehicle, these postponements allegedly last anywhere from just a few months to over a year. The sources from the suppliers claim that in some cases these tweaks are for engineering and design changes. The next-gen Ram 1500 reportedly has among the shorter delays and is being pushed from mid-2017 to November 2017, according to Reuters. Also, the much-discussed future Jeep Wrangler is allegedly moving a little later to July 2017. Among the vehicles purportedly seeing longer delays, the next-gen Grand Cherokee could get pushed back about a year to 2018. That then forces the launch of the three-row, luxury Grand Wagoneer to be even further away. Jeep's upcoming C-segment CUV and the all-new Chrysler 300, Dodge Charger, and Challenger might also see postponements. The one brand allegedly seeing an accelerated plan is Alfa Romeo. Without going into detail, the sources from these suppliers claim that the Italian automaker is getting even more vehicles for its lineup and could get them even faster than planned. "Those plans need to be flexible and fluid, with the potential to add some vehicles, pull some forward and extend the life cycle of others," FCA said to Reuters about all of these allegations. "We look at these programs on a vehicle-by-vehicle basis." Investment in the auto industry has been a major topic for FCA CEO Sergio Marchionne as of late. He believes consolidation is necessary so that companies aren't burning money on the same projects. Related Video: News Source: ReutersImage Credit: Bill Pugliano / Getty Images Plants/Manufacturing Alfa Romeo Chrysler Dodge Fiat Jeep RAM Sergio Marchionne FCA fca us

The Dodge Demon is leaked in Fast 8 video with Vin Diesel

It's only week two of the twelve-part Dodge Demon teaser roll out, and it already appears the metaphorical Hellcat is out of the bag. A YouTube video featuring Vin Diesel discussing The Fate of the Furious ( Fast 8) has what are almost certainly two Dodge Challenger Demons parked right in the background. So much for three months worth of build up and mystique. The two cars in the video appear to have the new logo affixed to the fender, right where the current Hellcat logo resides. In addition, the wheels and the massive hood scoop both appear to be the same relative shape as the ones briefly flashed in the latest teaser video. While we can't be 100 percent certain this is really a Demon, all the evidence points to yes. Even if this spoiled Dodge's plans, actually seeing the car here makes us even more excited for the full reveal. We still don't know all the final specs, save that it'll be 200 lbs lighter, so there is still some mystery to be had. The Challenger and Charger Hellcat twins, some of the most brazen and brutish machines currently on the road, were already cranked up to 11. The Demon, with its wide fender flares and comically large hood scoop looks makes the standard car look tame by comparison. We can't wait. Related Video: News Source: YouTube Design/Style Dodge Coupe Performance dodge demon Vin Diesel dodge hellcat dodge challenger hellcat