4x4 Cummins 24-valve Diesel Dualie -- Original Window Sticker -- Extra Clean! on 2040-cars

Auto blog

Stormtrooper Dodge Charger Episode IV: A New Soap

We spent a day with a Dodge Charger that looks like a Stormtrooper helmet and made a few videos. In this one, the Charger meets the car wash. May the force be with the dryer. Read about the car and watch the rest of the videos here.

2015 Dodge Viper getting small increase in power

The Viper is used to being the most powerful car in the Dodge and SRT stables, but the arrival of the 2015 Dodge Challenger SRT Hellcat means that's no longer the case. The serpentine supercar is, however, reportedly getting a small boost in output for 2015, amounting to all of five horsepower.
The increase was uncovered by Road & Track courtesy of the SAE J1349 certification process to which Detroit's Big Three automakers submit themselves and which reports the Viper's output at 645 hp instead of the 640 it was rated at until now. There are a hundred factors that could have contributed to the relatively mild boost in output (best guess? nothing at all changed...), but we doubt anyone's going to complain about some extra horses under the hood.
The five-horsepower boost brings the Viper that much closer to the 650-hp Chevy Corvette Z06, not to mention the 707-hp Hellcat, but the Viper's impressive power-to-weight ratio ought to mean it'll have little problem keeping up in a straight line - which is just one of the reasons why Chrysler won't shoe-horn the Hellcat into the Viper: as R&T points out, the supercharged engine is too heavy and the blower makes it too tall to fit in the Viper's engine bay.

Mopar unveils Dodge Challenger Drag Pak [w/video]

Dodge is going drag racing, and it's doing it with an all-new version of the Challenger for NHRA's Sportsman class. FCA's Mopar parts and performance arm announced the new Challenger Drag Pak Friday, showing off a version with a 354-cubic-inch (that's a 5.8-liter, by the way), supercharged V8 and a 426-ci (7.0-liter), naturally aspirated V8 – both Hemis, of course – that can get the big coupes through the quarter-mile in "the eight-second range." While the two engines deliver similar performance, at their base, they're quite a bit different. The supercharged model uses a cast-iron block, while the 426 has aluminum for both the block and head. That said, both models get customized engine calibrations, and are mated to unique, race-spec automatic transmissions. But drag racing is about far more than just outright power. Mopar significantly updated the four-link rear suspension, adding a four-inch rear axle from Strange Engineering, along with an aluminum, nine-inch third member, while the rear-axle housing has been strengthened in general. Both the rear shocks and front struts can be adjusted for rebound and compression, too. Lightweight 15-inch wheels, meanwhile, are shod in super-sticky Hoosier drag radials, with nine inches of tread in back and 4.5 inches in front. The new Challenger Drag Pak should run the quarter-mile in "the eight-second range." In the cabin, there's an NHRA-spec roll cage, a Racepak gauge cluster, and a handsome pair of Sparco racing seats. Outside, supercharged models get blue decals, while naturally aspirated varieties get black stickers, although there's more to the new Challenger dragster's exterior than just its decals. Mopar tweaked the big-scoop hood, promising it's easier to get up to check on the engine, and the designers also added trailer tie-down straps in both the front and rear. While the dragster was the big news today, Mopar officials also announced the two enhanced Scat Pack kits for both the Dodge Charger and Challenger R/T. The 5.7-liter Hemi models gain an extra 56 horsepower and 30 pound-feet of torque in the Scat Pack 2 thanks to a new cam, valve springs, pushrods, and gaskets. The Scat Pack 3, meanwhile, adds 75 hp and 44 lb-ft, on top of the gains from the lower packages. That should be perfect for drivers who wish to snort in the face of their SRT 392-driving friends. The third stage adds a ported cylinder heads, as well as high-flow manifolds and catalysts.