2012 Dodge Ram 3500 6.7l H.o. Cummins Diesel 4x4 on 2040-cars

Auto blog

2018 Dodge Challenger SRT Demon sheds seats and insulation to drop weight

You've probably already heard that the 2018 Dodge Challenger SRT Demon will be lighter than the Hellcat Challenger – to tune of more than 200 pounds. What you probably don't know is that the Dodge team did it by dropping most of the seats, along with a few other tricks. The Demon loses 113 pounds by making the front passenger seat with its seatbelt (58 pounds) and back seat (55 pounds including restraints and floor mats) optional, which accounts for a large chunk of the weight loss compared to the Hellcat. The Demon also has unique 18-by-11-inch wheels, which are 16 pounds lighter than the Hellcat's, a manual tilt/telescope steering column instead of the powered one, which loses four pounds, and an 18-pound loss thanks to removing 23 noise, vibration, and harshness parts (the Demon will not be a quiet car, to say the least). Another 20 pounds is lost removing the trunk interior trim and spare tire. Still, the Demon gains 17 pounds thanks to the wide fender flares that accommodate the massive drag radials, which also add 3.5 inches to the car's width. For reference, the lightest Hellcat weighs 4,448 pounds with a manual transmission, and the automatic-equipped car comes in at 4,455 pounds. The Demon will be revealed in April before the New York Auto Show, and Dodge will continue to tease its latest satanic muscle couple weekly until then. Related Video: This content is hosted by a third party. To view it, please update your privacy preferences. Manage Settings.

Dodge Demon makes so much torque, it needs stronger driveline parts

Torque is a lovely thing, a sweet and wonderful force that twists and pulls and can help propel a two-ton metal box forward at comical speeds. Torque is also fickle and will bend and break those same metal parts without a second thought, which is why the new Dodge Demon is compensating for its increased torque with some new re-engineered and reinforced parts. And there's software intended to combat wheel hop, which one of the most dramatic ways torque can break stuff. Week 8's video, "Race-hardened Parts," gives a hint towards what all these new parts can do. While we still don't know how much torque the Demon will throw out, we do know it's enough to warrant an upgraded prop shaft, half shafts, and a differential housing. The Challenger Hellcat, which is the basis for the Demon, makes 650 pound-feet of torque already. The new parts will go a long way toward making sure the work from the Demon's engine is properly translated into motion by those Nitto drag radials. The new prop shaft uses high-strength steel, heat-treated stub-shafts, and increases the tube thickness by 20 percent for a 15 percent increase in torque capacity. Additionally, Dodge says the upgraded differential housing allows for a 30 percent increase in torque capacity by using heat-treated A383 aluminum alloy and a higher strength shot-peened gear set. The 41-spline half shafts that deliver 20 percent increased torque capacity through the use of high-strength low alloy steel and 8-ball joints. In addition to the hardware, the Launch Assist software has been tuned to help alleviate wheel hop. Dodge says the Demon is the first factory production car that uses wheel speed sensors to detect hop and momentarily cut torque to compensate. This means a driver can keep their foot planted on the floor while the computer sorts out the traction. Previously, the best solution was to back off the throttle to manually cut the load. Finally, the Dodge Demon will offer a four-point harness mounting bar as an optional accessory. The part will be supplied by Speedlogix and fits in place of the deleted rear seat. Customers can install the bar without having to hack apart their cars to find a proper mounting point. Look for more teasers and info on ifyouknowyouknow.com in the lead-up to the Demon's debut at the 2017 New York Auto Show. Related Video: Image Credit: FCA Dodge Performance dodge demon dodge hellcat

Dodge and Jeep recalling 895k SUVs for possibility of headliner fires

Dodge and Jeep are announcing recalls of a total of 895,000 Durango and Grand Cherokee models worldwide from the 2011 through 2014 model years. There's a possibility that the wiring in the sun visor can short circuit and cause a fire. It specifically affects vehicles built between January 5, 2010, and December 11, 2013, and there are approximately 651,000 of them in the US, 45,700 in Canada, 23,000 in Mexico and 175,000 outside of North America.
Screws that fasten the sunvisor to the headliner may pierce wires in the visor, if the part has been removed or serviced, potentially causing a fire risk. If the wires short circuit, they could overheat and potentially combust. The automakers report three injuries caused by this defect, and according to the investigation by the National Highway Traffic Safety Administration, "there may be a total of 52 unique fire incidents."
To fix the problem, Dodge and Jeep will inspect the vehicles for suspect wiring, and all of the models, whether damaged or not, will get a new sun visor spacer with a wire guide to stop the possibility of short circuits. According to the automakers' announcement, "this condition is not present in vehicles which have not had the headliner or vanity mirror serviced." They will notify affected owners, and repairs will begin in August.