2004 Dodge Ram 2500 Slt Quad Cab Hemi Low Miles. Nice Truck!!!! Look!!!! on 2040-cars

Auto blog

VW scandal, Alan Taylor on Vipers, and future cars | Autoblog Podcast #474

Episode #473 of the Autoblog Podcast is here. This week, Dan Roth chats with Sam Abuelsamid of Navigant Research about the just-announced deal pending between Volkswagen and the EPA, and Navigant's Transportation Outlook for 2025 to 2050. Alan Taylor, host of The Drive on ERN also visits the Podcast to talk about picking up his Viper ACR in Texas and driving it back to the West Coast. It all starts with the Autoblog Garage - check it out! Check out the rundown with times for topics, and thanks for listening! Autoblog Podcast #474 Topics VW/EPA deal Navigant Research Transportation Outlook Alan Taylor In The Autoblog Garage 2016 Lincoln MKX 2016 Volvo XC90 2016 Jeep Renegade Trailhawk Hosts: Dan Roth Guests: Sam Abuelsamid, Alan Taylor Rundown Intro & Garage - 00:00 VW/EPA - 25:51 Navigant Outlook - 38:47 Alan Taylor - 54:43 Total Duration: 01:13:11 Get The Podcast iTunes – Subscribe to the Autoblog Podcast in iTunes RSS – Add the Autoblog Podcast feed to your RSS aggregator MP3 – Download the MP3 directly Feedback Email – Podcast at Autoblog dot com Review the show in iTunes Podcasts Dodge Volkswagen

Dodge Demon makes so much torque, it needs stronger driveline parts

Torque is a lovely thing, a sweet and wonderful force that twists and pulls and can help propel a two-ton metal box forward at comical speeds. Torque is also fickle and will bend and break those same metal parts without a second thought, which is why the new Dodge Demon is compensating for its increased torque with some new re-engineered and reinforced parts. And there's software intended to combat wheel hop, which one of the most dramatic ways torque can break stuff. Week 8's video, "Race-hardened Parts," gives a hint towards what all these new parts can do. While we still don't know how much torque the Demon will throw out, we do know it's enough to warrant an upgraded prop shaft, half shafts, and a differential housing. The Challenger Hellcat, which is the basis for the Demon, makes 650 pound-feet of torque already. The new parts will go a long way toward making sure the work from the Demon's engine is properly translated into motion by those Nitto drag radials. The new prop shaft uses high-strength steel, heat-treated stub-shafts, and increases the tube thickness by 20 percent for a 15 percent increase in torque capacity. Additionally, Dodge says the upgraded differential housing allows for a 30 percent increase in torque capacity by using heat-treated A383 aluminum alloy and a higher strength shot-peened gear set. The 41-spline half shafts that deliver 20 percent increased torque capacity through the use of high-strength low alloy steel and 8-ball joints. In addition to the hardware, the Launch Assist software has been tuned to help alleviate wheel hop. Dodge says the Demon is the first factory production car that uses wheel speed sensors to detect hop and momentarily cut torque to compensate. This means a driver can keep their foot planted on the floor while the computer sorts out the traction. Previously, the best solution was to back off the throttle to manually cut the load. Finally, the Dodge Demon will offer a four-point harness mounting bar as an optional accessory. The part will be supplied by Speedlogix and fits in place of the deleted rear seat. Customers can install the bar without having to hack apart their cars to find a proper mounting point. Look for more teasers and info on ifyouknowyouknow.com in the lead-up to the Demon's debut at the 2017 New York Auto Show. Related Video: Image Credit: FCA Dodge Performance dodge demon dodge hellcat

Chrysler killing off the 200 Convertible, Dodge Avenger

When Chrysler rolled out the first-generation 200 to replace the Sebring range in 2010, it included replacements for both the sedan and the convertible. The Sebring Coupe, however, was left out of the mix. And now that the second-generation Chrysler 200 is descending upon us, Auburn Hills is paring things down even further. But this time, it's the convertible that reportedly isn't making the cut. Shame, too, since the rendering above shows what could have been quite an attractive droptop.
As our compatriots at Edmunds point out, sales of the convertible model accounted for less than five percent of overall Chrysler 200 sales, and at those numbers, the considerable cost of engineering a new drop-top couldn't be justified. With the Toyota Camry Solara and Volkswagen Eos also gone from the market (well, the VW isn't gone quite yet), the discontinuation of the Chrysler 200 Convertible leaves the affordable convertible segment largely to the sportier likes of the Ford Mustang and Chevy Camaro and smaller European offerings like the Mini Cooper and VW Beetle.
The Chrysler 200 Convertible isn't the only derivative being left behind with the new model: so too is the Dodge Avenger. That will leave a glaring hole in the Dodge lineup, with nothing to bridge the gap between the compact Dart and the larger Charger. Whether the Dodge brand has any plans to replace the Avenger with another model, not to be based on the 200, remains to be seen.